background image

10

350A4502P760

 

MARK HOLES

 

Select the vent option that your installation will require 

and proceed to that section:

Hood mounting screws (4)

13¾

13¾

 

Cabinet front

Center 

line

Electrical access 

hole (in cabinet 

bottom)

Wood shims 

(recessed-bottom 

cabinets only)

Vertical duct  

access hole

14

16

3

11

/

16

11/16

A. Outside top exhaust  

(Vertical duct–3

1

4

 x 10

 Rectangular)

• Use the diagram or the hood as a template and mark 

the locations on the cabinet for ductwork, electrical 

wiring and keyhole screw slots .

Cabinet Bottom

7

Wood shims 

(recessed-bottom cabinets only)

Cabinet front

Center line

Electrical 

access hole 

(in wall)

Hood mounting 

screws (4)

Horizontal duct  

access hole

Cabinet 

bottom

13¾

½

5

1

4

5

1

4

13¾

B. Outside rear exhaust  

(Horizontal duct–3

1

4

 x 10

 Rectangular)

• Use the diagram or the hood as a template and mark 

the locations on the cabinet for ductwork, electrical 

wiring and keyhole screw slots .

C.  Recirculating (non-vented ductless)

• Use the hood as a template and mark the locations 

 

on the cabinet for the electrical wiring and keyhole 

screw slots .

• Since the hood is to be recirculated (not to be vented 

outside), do not cut out any vent openings in the wall 

or cabinet bottom .

 

FOR 3

1

4

 x 10

 RECTANGLE DUCTED 

DISCHARGE INSTALLATIONS:

  Attach exhaust 

adaptor/damper

 over knockout 

opening with two exhaust adaptor screws . Make sure 

damper 

pivot

 is nearest to 

top/back edge

 of hood . 

Remove 

tape

 from damper flap . 

Up to 1

 side-to-

side adjustment

Tape

Top/back edge

Exhaust adaptor/damper 

(vertical discharge position 

shown)

Pivot

6

Installation Instructions

NOTE:

 The exhaust adaptor/damper can be installed 

up to 1 inch on either side of the hood center to 

accommodate off-center ductwork . In extreme off-center 

installations, one end of the duct connector may need to 

be trimmed to clear the electrical cable clamp .

5

1

4

5

1

4

1" = 2 .5 cm; 1' = 0 .3 m

Summary of Contents for JVE330



















Reviews: