background image

4

350A4502P760

To clean the hood surface, use a hot, damp 

cloth with a mild detergent suitable for 

painted surfaces . Use a clean, hot, damp 

cloth to remove soap . Dry with a dry, clean 

cloth .

Do not use steel-wool pads or other abrasive 

cleaners . They will scratch the surface . Wipe 

with a clean, hot, damp cloth after using 

cleansers . 

Painted Surfaces

 

(on some models)

WARNING:

Hg

 - Lamp contains Mercury.  Manage 

in accord with disposal laws.

 See www .

lamprecycle .org or 1-800-435-4448 .
For installation, handling and disposal 

precautions, refer to the fluorescent lamp 

packaging literature .

WARNING:

n

 To reduce the risk of electric shock, do 

not connect electrical power to the hood 

without both lamps in place.

CAUTION: 

n

 Do not touch the hood lamps when they 

are on. They may be hot enough to cause 

injury.

n

 To prevent injury from broken lamps, 

handle lamps carefully and do not operate 

hood without lamp lens covers in place.

 

 

This hood requires two Compact Fluorescent 

Lamps (CFL) with a GU24 base (included), 

maximum 15 watts .

To change the lamps:

 When installing or replacing a lamp, 

make sure that power to the light has 

been turned off . Never allow a lamp to 

come into contact with water .

 Remove the lens cover by sliding it in a 

horizontal direction and pulling it down 

and away from the hood .

 Grasp the lamp by the plastic base 

portion of the lamp and unscrew it .

 Replace with energy saving GE 15W 

Compact Fluorescent Lamp with GU24 

base GE Service Part:  WB08X10064.

Hood Lights

NOTE:

 Charcoal filters are not 

included with the hood. They 

must be ordered from your 

GE supplier.

If the model is not vented 

to the outside, the air will 

be recirculated through 

disposable charcoal filters that 

help remove smoke and odors .

The charcoal filters should 

be replaced when they are 

noticeably dirty or discolored 

(usually after 6–12 months, 

depending on hood usage) .

NOTE: 

DO NOT rinse, or put 

charcoal filters in an automatic 

dishwasher.

Note: 

If the hood in installed 

for recirculation mode, it is 

not E

nergy

 S

tar

®

 certified.

Charcoal Filters

 

(on some models)

The charcoal filters 

cannot be cleaned. 

They must be replaced.

Order Kit no. 

WB02X11000.

This kit can be ordered 

from your GE supplier.

The charcoal filters are clipped 

inside of each reusable metal 

grease filter.

Care and cleaning of the vent hood.

Stainless Steel Surfaces

 

(on some models)

Do not use a steel wool pad; it will scratch 

the surface.

To clean the stainless steel surface, use 

warm sudsy water or a stainless steel 

cleaner or polish . Always wipe the surface in 

the direction of the grain . Follow the cleaner 

instructions for cleaning the stainless steel 

surface .

Summary of Contents for JVE330



















Reviews: