background image

350A4502P760

3

HI

OFF

LO

FAN

LIGHT

OFF

ON

Using the hood controls. 

GEAppliances.ca

Throughout this manual, features and appearance may vary from your model.

 

FAN Control

 Press the rocker switch at the top to turn the fan on   

 

HI

 and at the bottom to turn it on 

LOW

 . The center  

 

position is 

OFF

 .

 

 Continuous use of the fan system while cooking helps 

keep the kitchen comfortable and less humid . It also 

reduces cooking odors and soiling moisture that create a 

frequent need for cleaning .

 

LIGHT Control

 

 Press the rocker switch at the bottom to turn the light 

ON

 

while cooking . Press the rocker switch at the top to turn 

the light 

OFF

 .

Rocker Switch Controls

Reusable Metal Grease Filters

The hood has 2 metal reusable grease 

filters .
The metal filters trap grease released 

by foods on the cooktop . They also help 

prevent flaming foods on the cooktop 

from damaging the inside of the hood .
For this reason, the filters must 

ALWAYS

 

be in place when the hood is used . The 

grease filters should be cleaned once a 

month, or as needed .

To remove, 

press the filter locks back 

and pull the filters down and out .

To replace, 

insert the rear filter tabs 

in the frame slots at the back of the 

opening . Push the filters up and lock 

them into place .

To clean the grease filters, 

soak them 

and then swish them around in hot 

water and detergent . Don’t use ammonia 

or ammonia products because they will 

darken the metal . Do not use abrasives 

or oven cleaners . Light brushing can be 

used to remove embedded dirt . Rinse, 

shake and let them dry before replacing . 

They may also be cleaned in an 

automatic dishwasher.

NOTE: 

Before cleaning, make sure the 

charcoal filters, if present, are unclipped 

and removed. See the Charcoal Filters 

section.

If it ever becomes necessary to replace 

the metal grease filters, they may be 

ordered from your GE supplier.

Filter locks

Care and cleaning of the vent hood.

Be sure electrical power is off and all surfaces are cool before cleaning or servicing any part of the vent hood.

Summary of Contents for JVE330



















Reviews: