background image

350A4502P760

9

 

REMOVE FILTERS

 

Remove the protective shipping film from the edges  

of the metal grease filters . Press the filter locks back and 

lift the filters out . Set them aside . 

 

REMOVE WIRING COVER  

FROM THE JUNCTION BOX

Remove the wiring cover from inside the hood .  

Set the cover and its mounting screw aside . 

Wiring 

cover

Mounting 

Screw

 

REMOVE WIRING KNOCKOUT

 

Remove either the top or the back wiring knockout as 

needed and install an approved strain relief clamp . 

Strain relief 

clamp

2

3

4

5

Filters

Installation Instructions

 

REMOVE DUCT KNOCKOUT(S)

 

If recirculating, 

non-vented ductless see note below and 

skip to Step 7 and proceed.

 

Using a flat blade screwdriver, remove the appropriate 

duct knockout(s)

 from the top or back of the hood . 

3

1

4

 x 10

 Rectangular 

vertical discharge. 

Remove top rectangular 

duct knockout only .

3

1

4

 x 10

 Rectangular 

horizontal discharge . Remove 

rear rectangular duct 

knockout only .

NOTE:

 If the hood is to be installed in a recirculating, 

non-vented ductless manner, order charcoal filters, kit 

number WB02X11000  for 30

 hood models . These kits 

can be ordered from your GE supplier . 

Skip to Step 7C and 

proceed.  

NOTE:

 If the hood in installed for recirculation mode, it is 

not E

nergy

 S

tar

®

 certified .

1" = 2 .5 cm; 1' = 0 .3 m

Summary of Contents for JVE330



















Reviews: