background image

12

350A4502P760

 

TROUBLESHOOTING CHECKLIST

If the hood seems to be operating at high speed when 

the control is not set on high, or if ventilation seems 

inadequate, check the following:

 Knockouts not removed from hood .

 Damper blade not opening .

 Reduced airflow because the duct is too small or the 

duct length is too long .

 The duct is blocked .

 Undersized or restrictive wall or roof cap .

 

REPLACE WIRING COVER

 

Replace the wiring cover .

 

CONNECT WIRING

 

Connect house black to hood black wire, house white 

to hood white wire, and house ground to hood green/

yellow wire . Securely tighten the strain relief clamp 

onto the house wiring .

19

20

17

 

CONNECT DUCTWORK TO HOOD

 

Use duct tape to make joints secure and air tight .

Note: 

Illustration shows rectangular to round duct adapter . 

Duct tape

16

 

REPLACE FILTERS

 

The installation is complete . Turn on power at service 

panel, and test for proper operation .

Installation Instructions

21

WARNING:

Hg

 - Lamp contains Mercury.  Manage in accord with 

disposal laws. 

See 

www.lamprecycle.org

 or 1-800-435-4448 .

For installation, handling and disposal precautions, refer to 

the fluorescent lamp packaging literature .

WARNING:

n

 To reduce the risk of electric shock, do not connect electrical 

power to the hood without both lamps in place.

CAUTION: 

n

 Do not touch the hood lamps when they are on. They may 

be hot enough to cause injury.

n

 To prevent injury from broken lamps, handle lamps 

carefully and do not operate hood without lamp lens covers 

in place.

This hood requires two Compact Fluorescent Lamps (CFL) 

with a GU24 base (included), maximum 15 watts .

To change the lamps:

 When installing or replacing a lamp, make sure that 

power to the light has been turned off . Never allow a 

lamp to come into contact with water .

 Remove the lens cover by sliding it in a horizontal direction 

and pulling it down and away from the hood .

 Grasp the lamp by the plastic base portion of the lamp 

and unscrew it .

 Replace with energy saving GE 15W Compact Fluorescent 

Lamp with GU24 base GE Service Part:  WB08X10064.

INSTALL LAMPS

 

 FOLLOW ELECTRICAL CODE

 

Complete the electrical wiring according to National 

Electrical Code and local codes .

 

NOTE:

 This hood must be permanently grounded .

 Connect 

house wiring

 (120 VAC) to hood wiring .

18

1" = 2 .5 cm; 1' = 0 .3 m

Summary of Contents for JVE330



















Reviews: