background image

Problem 

Possible Causes 

What To Do

The air is not always 

The heat pump is not  

  This is normal. The heat pump will produce warm air 

cool or hot during  

producing hot air. 

  but not as hot as air produced when the higher-cost 

operation 

 

  electric heat is used.

 

The Smart Fan Auxiliary  

• This causes the fan to blow room temperature air 

 

Controls may be set to  

  even when the compressor or heater cycles off. 

 continuous 

fan. 

 

The continuous air movement provides better  

 

 

  overall temperature control in the cool mode. 

  

 

See 

Smart Fan – Cooling/Heating on page 5.

The air does not feel 

The heat pump alone 

• Use the Electric Heat Option. This turns off the 

warm enough during 

produces air that feels 

  heat pump and warms with electric heat only. 

heating operation 

cooler than desired. 

  NOTE: Use of this option will result in increased energy  

  

 

consumption.

The unit is not 

The Smart Fan Auxiliary  • 

See 

Smart Fan – Cooling/Heating on page 5. 

blowing out air 

Controls may be set to cycle.   

The electric heating 

The power cord is not 

• Remove the room cabinet and make sure that the  

and fan features do 

firmly attached. 

  black connector on the end of the power cord is  

not work 

 

  firmly engaged.

Temperature display 

The compressor may   

• Set the operation control to OFF and then restart  

flashes 

have failed. 

  the unit. If the flashing light reappears within  

 

 

  30 minutes, call for service.

The unit does not 

Unit thermostat connections 

• Check aux mode 6 to be sure switch is “on” for Remote  

 

function after 

are incorrect.  

Thermostat.

installing Remote 

Wall Thermostat 

Aux mode 6 not set properly.  

• Verify wiring from Remote Wall TStat is correct to unit thermostat  

  

 

connector.

 

Transformer resets or opens 

• Wait 5 minutes to see if power resets. 

 

with short

 

 

 

   

 

23

Summary of Contents for Zoneline AZ45





























Reviews: