background image

Before you call for service…

Troubleshooting Tips  

Save time and money! Review the charts on the following 

pages first and you may not need to call for service.

Problem 

Possible Causes 

What To Do

Zoneline does 

The unit is  

  Make sure the Zoneline plug is pushed completely  

not start unplugged. 

 

into the outlet.

 

The power cord is not 

  Remove the room cabinet and make sure that the  

 firmly 

attached. 

  black connector on the end of the power cord is  

 

 

 firmly 

engaged.

 

The fuse is blown/circuit 

  Check the house fuse/circuit breaker box and replace 

 

breaker is tripped. 

  the fuse or reset the breaker.

 

The unit is waiting for 

  This is normal. The Zoneline will start again after  

 

the compressor overload 

  it resets. 

 

protector to reset.

 Power 

failure. 

  If power failure occurs, set the mode control to OFF. 

 

 

  When power is restored, set the mode control to the  

  

 

desired 

setting.

 

 

  There is a protective time delay (up to 3 minutes) to  

 

 

  prevent tripping of the compressor overload. For this  

 

 

  reason, the unit may not start normal heating or cooling  

 

 

  for 3 minutes after it is turned back on.

 

The power cord current  

  Press the RESET button located on the power cord plug  

 

interrupter device is tripped. 

  or the box near the plug.

 

 

  If the RESET button will not stay engaged, discontinue use  

 

 

  of the Zoneline and contact a qualified service technician.

Zoneline does not cool 

Indoor airflow  

  Make sure there are no curtains, blinds or furniture 

or heat as it should is 

restricted. 

 

blocking the front of the Zoneline.

 

Outdoor airflow is 

  Make sure the rear grille is not restricted. This can  

 

restricted or recirculated. 

  cause the unit to cycle off due to the compressor  

  

 

overload 

protector.

 

 

  Outdoor grille must have a minimum of 65% free area.  

 

 

  Non-GE grilles may be too restrictive for proper  

 

 

  performance. Consult your salesperson for assistance.

 

The temp control may 

  Turn the control to a lower or higher setting. 

 

not be set properly. 

  NOTE: The temperature limiter may be limiting the  

  

 

temperature 

range.

 

The air filter is dirty. 

  Clean the filter at least every 30 days. 

 

 

  See the Operating Instructions section.

 

The room may have  

  When the Zoneline is first turned on you need to 

 

been hot or cold. 

  allow time for the room to cool down or warm up.

 

Outdoor air is  

  Set the vent control to the closed position. 

 

entering the room.

Burning odor at the start  Dust is on the surface  

• This can cause a “burning” odor at the beginning of 

of heating operation 

of the heating element. 

  the heating operation. This odor should quickly fade.

22

Summary of Contents for Zoneline AZ45





























Reviews: