GE SymVeo SV-XP1 User Manual Download Page 10

Page: 10 / 60

SymVeo IP Camera

User Manual

Inspect the package and contents for visible damage. If any
components are damaged or missing, do not use the unit; contact
the supplier immediately. If you need to return the unit, you must
ship it in the original box.

Other required equipment

You might also need some or all of the following for proper
installation and use of this product:

•

12 VDC 1 Amp Power Supply.

•

Lens.

•

PC, to set the IP address and view video with the
SymNav user interface.

•

CCTV for local monitoring.

Refer to your lens and CCTV monitor manuals for installation
and setup information.

References

If you want to investigate related topics, these other documents
may prove helpful:

•

GE Security.

SymDec User Manual (

0150-0285

)

•

GE Security.

SymDec-4 User Manual (

0150-0304

)

•

GE Security.

SymNav User Manual (

0150-0303

)

Summary of Contents for SymVeo SV-XP1





























































Search results

Summary of Contents for SymVeo SV-XP1

Reviews:

Related manuals for SymVeo SV-XP1

Brands by name

Popular brands

GE SymVeo SV-XP1, User Manual

Search results

Summary of Contents for SymVeo SV-XP1

Reviews:

Related manuals for SymVeo SV-XP1

Brands by name

Popular brands