manualshive.com logo in svg

GE SymVeo SV-XP1, User Manual, Page: 11 / 60

Share
Download
GE SymVeo SV-XP1 User Manual Download Page 11

5

Installation

Making power connections

To make power connections, see 

Figure 2

 on page 6 and do the 

following:  

1. With a screwdriver, loosen the DC12V and GND 

terminal screws on the terminal block.

2. Connect a 12 VDC 1 Amp power supply to the terminal 

block.

Note:

The terminal block is not polarity-sensitive. Either power 
lead can be connected to either terminal connector.

3. Retighten the terminal screws until snug, ensuring that 

the power leads are secure.

4. Supply power to the unit by plugging the power supply 

into a proper power source.

The power LED (lower left) illuminates to show that the camera 
is receiving power. If it does not illuminate, check the terminal 
block connections and the power source.  

CAUTION

Use direct plug-in UL listed power supplies marked 
Class 2 or LPS (limited power source) of the required 
output rating as listed on the unit. Select an output 
of 1 amp minimum.

Complete all instruction steps before supplying 
power to the unit.

Summary of Contents for SymVeo SV-XP1





























































Reviews:

No comments