manualshive.com logo in svg

GE ReadyToProcess WAVE 25, Operating Instructions Manual

Share
Download
GE ReadyToProcess WAVE 25 Operating Instructions Manual Download Page 90

4.3

Software installation

About this section

This section describes how to perform a complete UNICORN 7.0 installation on a stand-
alone workstation (Full installation). Instructions on how to configure an e-license, define
a system, and set up a system printer are also included.

For other types of installations, contact your GE representative for support.
This includes network installations when you want to access the
ReadyToProcess WAVE 25 system from several client computers or control
more than one system from a single computer, or to run the system from a
third-party controller.

Note:

Additional information about software installation and configuration is available in the
UNICORN Administration and Technical manual.

In this section

See page

Section

91

4.3.1 Install UNICORN software

94

4.3.2 Configure an e-license

101

4.3.3 Define the system

90

ReadyToProcess WAVE 25 Operating Instructions 29009597 AD

4 Installation

4.3 Software installation

Summary of Contents for ReadyToProcess WAVE 25













































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands