manualshive.com logo in svg

GE ReadyToProcess WAVE 25, Operating Instructions Manual

Share
Download
GE ReadyToProcess WAVE 25 Operating Instructions Manual Download Page 124

5.2.1

Start the system and log on to UNICORN

Follow the instructions below to start the system and log on to UNICORN. The workstation
must have a valid e-license.

See Section 4.3.2 Configure an e-license, on page 94 for more information about e-licenses.

Action

Step

Switch on the client computer.

1

Start the UNICORN software.

2

Provide your User Name and Password to log on to UNICORN. Access cre-
dentials are assigned by your UNICORN administrator. According to the
properties of your user account, you may be able to select an Access Group.

3

Note:

If Use Windows Authentication is checked, you may log on using your Win-
dows username and password.

Press the Power switch to start the rocker.

4

Result: The Power button flashes green during start-up, and then lights
steadily when the rocker is operational.

124

ReadyToProcess WAVE 25 Operating Instructions 29009597 AD

5 Operation

5.2 Start and configure the system
5.2.1 Start the system and log on to UNICORN

Summary of Contents for ReadyToProcess WAVE 25













































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands