GE ReadyToProcess WAVE 25 Operating Instructions Manual Download Page 19

Page: 19 / 172

WARNING

Do not use ReadyToProcess WAVE 25 if it is not working properly,
or if it has suffered any damage, for example:

•

damage to the power cord or its plug

•

damage caused by dropping the equipment

•

damage caused by splashing liquid onto it

NOTICE

Any computer used with the equipment must comply with EN/IEC
60950-1, and be installed and used according to the manufacturer's
instructions.

Flammable liquids and explosive
environment

WARNING

ReadyToProcess WAVE 25 is not designed to handle flammable
liquids.

WARNING

ReadyToProcess WAVE 25 is not approved for work in a potentially
explosive atmosphere.

Personal protection

WARNING

Always use appropriate Personal Protective Equipment (PPE) during
operation and maintenance of this product.

ReadyToProcess WAVE 25 Operating Instructions 29009597 AD

2 Safety instructions

2.1 Safety precautions

Summary of Contents for ReadyToProcess WAVE 25













































































































































































Search results

Summary of Contents for ReadyToProcess WAVE 25

Reviews:

Brands by name

Popular brands

GE ReadyToProcess WAVE 25, Operating Instructions Manual

Search results

Summary of Contents for ReadyToProcess WAVE 25

Reviews:

Brands by name

Popular brands