GE ReadyToProcess WAVE 25 Operating Instructions Manual Download Page 45

Page: 45 / 172

Description

Part

Rocker platform

Temperature sensors

Rocker base

Power button

Location of adjustable foot

Power button

The Power button indicates the status of the rocker according to the list below.

Description

Image

Light indicator

The power is OFF.

No light

The rocker is starting up.

Green flashing light

The power is ON and the rocker is opera-
tional.

Green steady light

The rocker failed to connect to other
components in the system.

Red flashing light

Indicates an error of the rocker.

Red steady light

ReadyToProcess WAVE 25 Operating Instructions 29009597 AD

3 System description

3.2 ReadyToProcess WAVE 25 rocker

Summary of Contents for ReadyToProcess WAVE 25













































































































































































Search results

Summary of Contents for ReadyToProcess WAVE 25

Reviews:

Brands by name

Popular brands

GE ReadyToProcess WAVE 25, Operating Instructions Manual

Search results

Summary of Contents for ReadyToProcess WAVE 25

Reviews:

Brands by name

Popular brands