manualshive.com logo in svg

GE ReadyToProcess WAVE 25, Operating Instructions Manual

Share
Download
GE ReadyToProcess WAVE 25 Operating Instructions Manual Download Page 21

Power supply

WARNING

Supply voltage. Before connecting the power cord, make sure that
the supply voltage at the wall outlet corresponds to the marking
on the instrument.

WARNING

Protective ground. bioreactor stand-alone instruments must al-
ways be connected to a grounded power outlet.

WARNING

Only use grounded power cords delivered or approved by GE.

WARNING

Access to power switch and power cord with plug. Do not block
access to the power switch and power cord. The power switch
must always be easy to access. The power cord with plug must
always be easy to disconnect.

WARNING

Disconnect power. Always disconnect power from the equipment
before connecting the ReadyToProcess WAVE 25 units to any other
instrument.

ReadyToProcess WAVE 25 Operating Instructions 29009597 AD

21

2 Safety instructions

2.1 Safety precautions

Summary of Contents for ReadyToProcess WAVE 25













































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands