GE PACSystems* RX3i Command Line Interface Manual Download Page 113 | Manualshive

Page: 113 / 116

background image

telnetd

GFK-2572

Chapter 3 Modify-Level Commands

3-21

3

Changing the Maximum Number of Telnet Connections

Step 1. Change the maximum connections.

Screen Display

device-name= telnetd 4
Max telnet Connections changed to 4
telnet changes will not take effect until next powerup or restart
device-name=

Step 2. Restart or power cycle the PNC. Use

show telnet

to display the Telnet status.

Screen Display

{Power-cycle occurs}

device-name> show telnet
01-JAN-2000 05:44:17.0000
<<< Telnet Info >>>
telnet Status: Enabled
Max telnet Connections: 4
Active telnet Connections: 1
device-name>

Disabling Telnet Connections

Step 1. Use no telnetd to disable all telnet connections.

Screen Display

device-name= no telnetd
telnet changes will not take effect until next powerup or restart
device-name=

Step 2. Restart or power cycle the PNC. Use

show telnet

to display the Telnet status.

Screen Display

{Power-cycle occurs}

device-name> show telnet
01-JAN-2000 05:44:17.0000
<<< Telnet Info >>>
telnet Status: Disabled
Max telnet Connections: 0
Active telnet Connections: 0
device-name>

«
...
111
112
113
114
115
...
»

Summary of Contents for PACSystems* RX3i





















































































































Reviews:

No comments

Related manuals for PACSystems* RX3i

Brand: Febco Pages: 4

Brand: Cisco Pages: 48

Brand: IBM Pages: 105

Brand: Yardney Pages: 8

Brand: tams elektronik Pages: 12

Brand: MAKOT Pages: 6

Brand: VAT Pages: 39

Brand: Samson Pages: 124

Brand: Samson Pages: 86

Brand: VAC Pages: 5

Brand: Ziton Pages: 28

Brand: Unico Pages: 164

Brand: DANIEL Pages: 48

Brand: Saluki Pages: 13

Brand: PUTCO Pages: 2

Brand: FrSky Pages: 2

Brand: TUYA Pages: 28

MultiLoad II EXL

Brand: Toptech Pages: 83

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands