GE eBike BASIC Service Manual Download Page 82

Page: 82 / 234

- 82 -

eBike II, eBike II L, eBike II EL

2018112-069 Rev. F

ountIng

tHe

andleBar

• Remove the two screws (a) from the clamping plate.

• Holding the clamping plate, turn the clamping lever

(b) counterclockwise and remove.

• Take off the clamping plate.

• Install the handlebar (handles downward) and secure

with the clamping plate.

• Turn the screws (a) in and tighten moderately.

• Screw in clamping lever (b) by turning it clockwise and

tighten moderately.

aKing

off

the

claMping

plate

ounting

the

handlebar

Note

• When mounting the handlebar, it should first point down

until the control terminal has been installed.

• Then bring the handlebar to the correct position and

secure by tightening the clamping lever and the screws.

• At the eBike comfort you can additionally adjust the

height of the handlebar to any level by means of a clam-
ping lever.

Summary of Contents for eBike BASIC











































































































































































































































Search results

Summary of Contents for eBike BASIC

Reviews:

Related manuals for eBike BASIC

Brands by name

Popular brands

GE eBike BASIC, Service Manual

Search results

Summary of Contents for eBike BASIC

Reviews:

Related manuals for eBike BASIC

Brands by name

Popular brands