GE Digital Energy 1018959 Operating Manual Download | Manualshive

Page: 51 / 69

background image

Address Description

Notes

10X32 -

Not

Used

(Reserved)

10X33

upsStatusEcomodeIsOn

Ecomode is ON.

10X34

upsStatusBatteryIsCharging

Battery is being charged.

10X35

upsStatusBatteryIsDischarging

The UPS is drawing power from the batteries. Identical to

upsAlarmOnBattery

.

10X36

upsStatusAlarmIsActive

UPS has a general fault. Identical to

upsAlarmGeneralFault

.

10X37 upsStatusRectifierIsOn Rectified

is

ON.

10X38

upsStatusStopOperation

The remaining battery run time is less than or equal to

upsConfigLowBattTime

or any other condition exist, such

that the output will be disconnected in a short time.

10X39

upsStatusOnBypass

The Bypass is presently engaged on the UPS. Identical to

upsAlarmOnBypass

.

10X40

upsStatusMainsBypassOK

All input conditions on the Bypass are OK. Reciprocal to

upsAlarmBypassBad

.

10X41

upsStatusMainsRectifierOK

All input conditions on the rectifier are OK. Reciprocal to

upsAlarmInputBad

.

10X42

upsStatusDetourIsOn

The manual deviation is on.

10X43

upsStatusAcousticAlarmIsOn

The acoustic alarm is on, as a consequence of a new fault.

10X44 upsStatusServiceCheck

A

general maintenance or a specific UPS component check

is required.

10X45

upsStatusInverterIsOn

The Inverter is switched on.

10X46

upsStatusNotInParallel

The UPS belongs to a parallel system but does not supply

the load (disconnected).

10X47

upsStatusResetLoadOff

The load is not supplied and special action has to be

performed prior to be able to restart.

10X48

upsStatusLoadOff

The load is not supplied

10X49 upsStatusBoostMode

Boost

mode

10X50 upsStatusBuckMode

Buck

mode

10X51

upsStatusIemModeIsOn

IEM (Intelligent Energy Management) mode is active

10X52 upsStatus5thFilterIsOn

5

th

order harmonic filter is inserted

(SCR-based rectifier only)

10X53 upsStatus11thFilterIsOn

11

th

order harmonic filter is inserted

(SCR-based rectifier only)

10X54

upsStatus2ndRectifierBridgeIsOn

For units featuring two separate rectifier bridges (typically

large 3-ph UPSs), the 2

nd

rectifier bridge is on.

10X55

-

Reserved for future enhancements

10X56

-

Reserved for future enhancements

10X57

-

Reserved for future enhancements

10X58

-

Reserved for future enhancements

10X59

-

Reserved for future enhancements

10X60

-

Reserved for future enhancements

10X61

upsGlobalParallelValues

The set of registers pertains to the whole parallel system
rather than specific UPS in the system.

10X62

-

Reserved for future enhancements

10X63

-

Reserved for future enhancements

10X64

-

Reserved for future enhancements

NOTE

: Registers 10X26 – 10X31 hold different contents in 1-ph and 3-ph UPS.

Registers 10X33 – 10X64 are only available on 3-ph UPS.

NOTE

: GT Series 5-10kVA UL UPSs are 2-ph systems.

In this case, the L-L voltage is mapped to Line3 Voltage registers.

Modifications reserved

Page 51/69

OPM_CNT_SNM_BAS_CRD_1GB_V014.doc

Operating Manual

SNMP/Web Adapter

«
...
49
50
51
52
53
...
»

Summary of Contents for Digital Energy 1018959






































































Reviews:

No comments

Related manuals for Digital Energy 1018959

FBIP-21 BACnet/IP

Brand: ABB Pages: 2

Brand: Radicom Research Pages: 9

Brand: Tamio Pages: 2

Brand: Basalte Pages: 2

POCKET ETHERNET ADAPTER III

Brand: Xircom Pages: 93

Brand: Pace Pages: 15

Brand: VSmart Pages: 9

Brand: Macherey-Nagel Pages: 21

Notebook Computer Universal 30W Power...

Brand: Radio Shack Pages: 36

Brand: Hamlet Pages: 4

PRESTO GIGABIT SERVER PCIe

Brand: Sonnet Pages: 4

Brand: Verizon Pages: 21

Brand: Crown Pages: 12

Brand: Mitsubishi Electric Pages: 3

MELSEC FX3U-485ADP-MB

Brand: Mitsubishi Electric Pages: 8

FX3U-485ADP-MBH

Brand: Mitsubishi Electric Pages: 2

PAC-USWHS002-WF-2

Brand: Mitsubishi Electric Pages: 8

Brand: Mitsubishi Electric Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands