manualshive.com logo in svg

GE Digital Energy 1018959, Operating Manual

Share
Download
GE Digital Energy 1018959 Operating Manual Download Page 31

3.3.7 

UPS Control 

page (1-ph/SP units ONLY) 

The UPS control page mainly controls UPS shutdown and reboot behaviour. As previously stated, these 
commands will impact the UPS and may have effect on any load applied to the UPS. It is therefore 
important to fully understand the consequences of any settings performed through this page.  
 

Parameter Name 

Description 

Shutdown type 

The action to be taken when the UPS is commanded to shutdown 
  1 – output 

The output of the UPS is switched off 

  2 – system 

The entire UPS system is switched off 

Shutdown after delay 

Specifies a time (in seconds) after which the UPS will shutdown 
  -1 disables the procedure

 

   0 immediate shutdown  

Startup after delay 

Specifies a time (in seconds) after which the UPS will start-up  
  -1 disables the procedure

 

   0 immediate start-up 

Reboot  

The UPS will shutdown immediately, and will remain off for the specified time (in 

seconds), after which the UPS will restart  

  -1 disables the procedure 

Auto-Restart 

On – the UPS will restart right after the shutdown 

Off – the UPS will not restart after the shutdown 

 

Caution!

 These commands may switch off the UPS output, therefore leaving the load with no power. 

Make sure you fully understand the effect on the UPS and on the load before injecting any of these 
commands. Make sure that it is safe to perform the described operation for both the UPS and the load. 
 
 
 
 
 

3.3.8  UPS Config page 

The page lists the main UPS configuration parameters. Normally, these parameters are pre-configured 
at the factory and there is no need to change them. Furethermore, forcing an incorrect configuration 
may impair the UPS functionalities and severly affect the load. It is therefore recommended not to alter 
any configuration settings unless informed and instructed to do so.  
 
 
 
 
 

3.3.9  UPS Service page (3-ph version ONLY) 

The page lists UPS diagnostic information. This information is intended for diagnostic analysis by GE 
Service Engineers – the data provided is not expected to be meaningful for the end user. 
The diagnostic information can be exported by pressing the 

Highlight

 button and copying the selected 

text (e.g. CTRL+C) to a separate application in order to be sent to a GE Customer Service Centre. 
 
 

Modifications reserved 

Page 31/69 

OPM_CNT_SNM_BAS_CRD_1GB_V014.doc 

Operating Manual 

SNMP/Web Adapter

 

Summary of Contents for Digital Energy 1018959






































































Reviews:

No comments

Brands by name

Popular brands

Load more brands