GE Digital Energy 1018959, Operating Manual

Page: 50 / 69

Discrete Inputs (1xxxx) – Function code 02: Read Discrete Input
Address Description Notes
10X01 upsAlarmBatteryBad One or more batteries have been determined to require
replacement.
10X02 upsAlarmOnBattery The UPS is drawing power from the batteries.
10X03 upsAlarmLowBattery The remaining battery run-time is less than or equal to
upsConfigLowBattTime .
10X04 upsAlarmDepletedBattery The UPS will be unable to sustain the present load when
and if the utility power is lost.
10X05 upsAlarmTempBad A temperature is out of tolerance.
10X06 upsAlarmInputBad An input condition is out of tolerance.
10X07 upsAlarmOutputBad An output condition (other than OutputOverload ) is out of
tolerance.
10X08 upsAlarmOutputOverload The output load exceeds the UPS output capacity.
10X09 upsAlarmOnBypass The Bypass is presently engaged on the UPS.
10X10 upsAlarmBypassBad The Bypass is out of tolerance.
10X11 upsAlarmOutputOffAsRequested The UPS has shutdown as requested, i.e., the output is off.
10X12 upsAlarmUpsOffAsRequested The entire UPS has shutdown as commanded.
10X13 upsAlarmChargerFailed An uncorrected problem has been detected within the UPS
charger subsystem.
10X14 upsAlarmUpsOutputOff The output of the UPS is in the off state.
10X15 upsAlarmUpsSystemOff The UPS system is in the off state.
10X16 upsAlarmFanFailure The failure of one or more UPS fans has been detected.
10X17 upsAlarmFuseFailure The failure of one or more fuses has been detected.
10X18 upsAlarmGeneralFault A general fault in the UPS has been detected.
10X19 upsAlarmDiagnosticTestFailed The result of the last diagnostic test indicates a failure.
10X20 upsAlarmCommunicationsLost A problem has been encountered in the communications
between the agent and the UPS.
10X21 upsAlarmAwaitingPower The UPS output is off and the UPS is awaiting the return of
input power.
10X22 upsAlarmShutdownPending A Shutdown countdown is underway.
10X23 upsAlarmShutdownImminent The UPS will turn off power to the load in less than 5
seconds; this may be either a timed shutdown or a low
battery shutdown.
10X24 upsAlarmTestInProgress A test is in progress.
10X25 upsAlarmReceptacleOff One or more receptacles are switched off.
10X26 VoltageOnOutput (1-ph only)
upsAlarmHighSpeedBusFailure
(3-ph only)
A voltage has been detected on output in a unforeseen
situation
A problem on the High Speed Bus communication is
detected
10X27 DCLinkVoltageBad (1-ph only)
upsAlarmHighSpeedBusJACRCFailure
(3-ph only)
The DC Link Voltage reached a high level.
A CRC problem on the Highspeed Bus JA is detected.
10X28 InputCircuitFailure (1-ph only)
upsAlarmConnectivityBusFailure
(3-ph only)
ByBf micro processor, IC converter, BF relay or charger is
defect.
A problem on the Connectivity Bus communication is
detected
10X29 ChargeConverterError (1-ph only)
upsAlarmHighSpeedBusJBCRCFailure
(3-ph only)
Charge converter or DC Capacitors are defect.
A CRC problem on the Highspeed Bus JB is detected.
10X30 BypassDefect (1-ph only)
UpsAlarmCurrentSharing (3-ph only)
Bypass is not able to hold Output Voltage.
The System detects an high current sharing on the parallel
system.
10X31 PhaseNeutralReversal (1-ph only)
UpsAlarmDCRipple (3-ph only)
There is a voltage between ground and neutral (input
reversed).
The System detects an high ripple voltage on one DC link.
Modifications reserved Page 50/69
OPM_CNT_SNM_BAS_CRD_1GB_V014.doc Operating Manual SNMP/Web Adapter