background image

Window 

Instillation in Window

 26” Wide

● 

Follow all instructions on pages

7-9 except steps 1 through 6 on

page 9.

● 

Use foam 

 to fill any openings

between the sides of the cabinet
and the window stop molding.

Installation Other Than

 Mounting

In order to install the appliance
with more of it projectin

into

the room, it will be necessary to
relocate the top retaining bar and

the bottom tie bar.

1. Check to make sure the cabinet’s

side louvers will not be blocked
when the unit is moved farther into

the room.

2. Remove the top retainer bar
cabinet side seals, and bottom tie
bar from the cabinet. Relocate them
for the desired projection into the

room.

3. Using the top retaining bar and
cabinet side seals as templates,
locate and drill five 7/32” mounting

holes in the top of the cabinet and
three on each cabinet side.

Top Retainer Bar

7/32” 

Holes

, Cab[net

 Tie Bar

4. Use sealing material (furnished)

 Drain

A condensate drain is provided to
divert excess water when the air
conditioner is installed over a

doorway or sidewalk.

Caution: Do not drill a hole in

the base pan.

1. Pry the cap plug from the

condensate drain (located on the
underside of the base pan). Use a

3/8” pipe tap and fully thread the
condensate drain.

I

Cap 

 

Condensate 

J

2. Screw a 3/8” pipe fitting into the
condensate drain. The fitting should
protrude approximatel

 above

the base pan when fully threaded
into the condensate drain.

Condensate Drain

Base Pan

Condensate Drain

3. If an open drain source is used
to dispose of condensate, plastic or
rubber tubing may be run directly
from the pipe fitting to the open

drain source. If a closed drain
source (internal 

 

is used, a “P” trap must be 

the 3/8” pipe fitting and the closed
drain source.

 Pipe

To Closed

Fitting

Drain Source

~&

 

“P” 

to fill the 

 in the cabinet top and

cabinet sides that became exposed
when the top retaining bar and
cabinet side seals were relocated.

5. Follow all instructions on pages
7 through 9.

10

Summary of Contents for AVD14













Reviews: