GE AKTAprime plus Operating Instructions Manual Download Page 60

Page: 60 / 68

Comments

EEC no.

CAS no.

Exposure

up to 2
months

Exposure

< 1 day

Chemical

Sodium bicarbon-
ate

Sodium bisulphate

Sodium borate

Sodium carbonate

231-598-3

7647-14-5

Sodium chloride

PVDF and borosili-
cate glass are af-
fected by long term
use.

215-185-5

1310-73-2

Avoid

Sodium hydroxide,
2 M

231-820-9

7757-82-6

Sodium sulphate

PEEK and titanium
are affected by
long term use.

Avoid

Sulphuric acid, dilut-
ed

Avoid

Sulphuric acid,
medium concentra-
tion

Silicone, PP and PE
are not resistant.

Avoid

Tetrachloroethy-
lene

ETFE, CTFE, PP and
PE are not resistant.

Avoid

Tetrahydrofuran

Pressure limit for
PEEK decreases.

Avoid

Toluene

200-927-2

76-03-9

Trichloroacetic
acid, 1%

200-929-3

176-05-1

Trifluoroacetic acid,
1%

200-315-5

57-13-6

Urea, 8M

PP and PE are af-
fected by long term
use.

Avoid

o-Xylene and p-Xy-
lene

ÄKTAprime plus Operating Instructions 28-9597-89 AB

7 Reference information

7.2 Chemical resistance

Summary of Contents for AKTAprime plus





































































Search results

Summary of Contents for AKTAprime plus

Reviews:

Brands by name

Popular brands

GE AKTAprime plus, Operating Instructions Manual

Search results

Summary of Contents for AKTAprime plus

Reviews:

Brands by name

Popular brands