manualshive.com logo in svg

GE AKTAprime plus, Operating Instructions Manual

Share
Download
GE AKTAprime plus Operating Instructions Manual Download Page 12

Navigation menu

The system is operated from the push buttons and LCD display at the front panel.

end

OK

Esc

pause

/cont

hold

/cont

feed

tube

Figure 1.2: Push buttons.

Description

Button

Find a specific menu option

or

Enter a menu.

OK

Return one menu level.

Esc

Interrupt method operation before the run is completed.

end

Stop manual operation.

Hold method time or volume and the gradient at the cur-
rent concentration. Pump and fraction collector continue
uninterrupted.

hold /cont

Continue the normal method operation.

Pause all operation without ending the method. All func-
tions, including pump and fraction collector, are stopped.

pause /cont

Continue the normal method operation.

Advance the fraction collector one position.

feed tube

12

ÄKTAprime plus Operating Instructions 28-9597-89 AB

1 Introduction

1.3 Instrument

Summary of Contents for AKTAprime plus





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands