GE AKTAprime plus Operating Instructions Manual Download Page 59

Page: 59 / 68

Comments

EEC no.

CAS no.

Exposure

up to 2
months

Exposure

< 1 day

Chemical

Silicone not resis-
tant.

200-579-1

64-18-6

Formic acid, 100%

200-289-5

56-81-5

Glycerol, 100%

Guanidinium hy-
drochloride

Silicone not resis-
tant. Pressure limit
for PEEK decreases.

Avoid

Hexane

Silicone not resis-
tant.

231-595-7

7647-01-0

Hydrochloric acid,
0.1 M

Silicone not resis-
tant. Titanium is af-
fected by long term
use.

Avoid

Hydrochloric acid,
> 0.1 M

200-661-7

67-63-0

Isopropanol, 100%

200-659-6

74-93-1

Methanol, 100%

Silicone not resis-
tant.

Avoid

Nitric acid, diluted

Elgiloy™ is affected
by long term use.

Avoid

Nitric acid, 30%

Titanium, alumini-
um oxide and glass
are affected by
long term use.

231-633-2

7664-38-2

Avoid

Phosphoric acid,
10%

209-529-3

584-08-7

Potassium carbon-
ate

231-211-8

7447-40-7

Potassium chloride

ETFE, PP and PE not
resistant.

Avoid

Pyridine

Sodium acetate

ÄKTAprime plus Operating Instructions 28-9597-89 AB

7 Reference information

7.2 Chemical resistance

Summary of Contents for AKTAprime plus





































































Search results

Summary of Contents for AKTAprime plus

Reviews:

Brands by name

Popular brands

GE AKTAprime plus, Operating Instructions Manual

Search results

Summary of Contents for AKTAprime plus

Reviews:

Brands by name

Popular brands