manualshive.com logo in svg

GE AKTAprime plus, Operating Instructions Manual

Share
Download
GE AKTAprime plus Operating Instructions Manual Download Page 24

CAUTION

The system uses high intensity ultra-violet light. Do not remove the
UV lamp while the system is running. Before replacing a UV lamp,
ensure that the lamp is disconnected to prevent injury to eyes.

If the mercury lamp is broken, make sure that all mercury is re-
moved and disposed according to national and local environmental
regulations.

NOTICE

Cleaning. Keep the instrument dry and clean. Wipe regularly with
a soft damp tissue and, if necessary, a mild cleaning agent. Let the
instrument dry completely before use.

2.2

Labels

In this section

This section describes the instrument labels and labels concerning hazardous substances
that are attached to the ÄKTAprime plus instrument. For information about marking of
the computer equipment, refer to the manufacturer’s instructions.

Labels on the instrument

The illustration below shows an example of the identification label that is attached to
the ÄKTAprime plus instrument.

24

ÄKTAprime plus Operating Instructions 28-9597-89 AB

2 Safety instructions

2.1 Safety precautions

Summary of Contents for AKTAprime plus





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands