manualshive.com logo in svg

GE AKTAprime plus, Operating Instructions Manual

Share
Download
GE AKTAprime plus Operating Instructions Manual Download Page 16

2

Safety instructions

About this chapter

This chapter describes safety compliance, safety labels, general safety precautions,
emergency procedures, power failure and recycling of ÄKTAprime plus.

2.1

Safety precautions

Introduction

The ÄKTAprime plus instrument is powered by mains voltage and handles pressurized
liquids that may be hazardous. Before installing, operating or maintaining the system,
you must be aware of the hazards described in this manual. Follow the instructions
provided to avoid personal injury or damage to the equipment.

The safety precautions in this section are grouped into the following categories:

•

General precautions

•

Using flammable liquids

•

Personal protection

•

Installing and moving the instrument

•

System operation

•

Maintenance

General precautions

Always follow these General precautions to avoid injury when using the ÄKTAprime plus
instrument.

WARNING

Do not operate ÄKTAprime plus in any other way than described
in the ÄKTAprime plus and PrimeView manuals. If the equipment
is used in a manner not specified by the manufacturer, the protec-
tion provided by the equipment may be impaired.

16

ÄKTAprime plus Operating Instructions 28-9597-89 AB

2 Safety instructions

Summary of Contents for AKTAprime plus





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands