manualshive.com logo in svg

GE 90-30 PLC, Installation And Hardware Manual

The GE 90-30 PLC User Manual is an essential guide for maximizing the use of this advanced programmable logic controller. With just a few clicks, users can easily download the manual for free from our website. Gain valuable insights and unleash the full potential of your GE 90-30 PLC today.

Share
Download
background image

5-4

Series 90-30 PLC Installation and Hardware Manual 

 

–

 

 August 2002

GFK-0356Q

5

 

RS-485

COMPATIBLE

SERIAL PORT

Figure 5-3.  CPU Serial Port Connector on Power Supply

Ŷ

 

This serial port is RS-485 compatible, and uses the GE SNP (Series Ninety Protocol)
protocol (slave only).  Breakfree SNP became the default protocol on all serial ports on the
Series 90-30 CPUs, starting with firmware release 9.00 for CPUs 350–364, and firmware
release 8.20 for CPUs 311–341.  For details, see page 5-13.

Ŷ

 

The serial port connector is only functional in a power supply that is installed in a baseplate
that also contains the CPU.  It is not functional on a power supply that is installed in an
expansion or remote baseplate.

Ŷ

 

Any device connected to the serial port that uses +5 VDC power from the Series 90-30 power
supply 

must be included

 in the calculation for maximum power consumption (see the heading

“Power Supply Loading Calculations” in Chapter 12).

Ŷ

 

All Series 90-30 CPUs have this serial port arrangement.  The 351, 352, and 363 CPUs have
additional serial ports, described in a later section of this chapter.

Caution

Care must be taken that common mode voltage specifications are met for
connections to this serial port.  Common mode conditions that exceed those
specified will result in errors in transmission and/or damage to Series 90
PLC components.  Common mode specifications are discussed in
Appendix A.  When the common mode voltage specification is exceeded, a
port isolator such as the GE IC690ACC903 must be used.  See
Appendix G for details on this port isolator.

Memory Volatility

The term volatility refers to the issue of whether or not a certain memory type retains or loses its
contents (data) when power is removed from it.

Ŷ

 

Volatile

 memory - memory that loses its contents when power is removed.  RAM memory is

inherently volatile.  Therefore, when the PLC is turned off, a backup battery is necessary if
data loss in RAM memory is to be prevented.

Ŷ

 

Non-volatile

 memory - memory that retains its contents when power is removed.  The various

types of PROM (Programmable Read-Only Memory) memory are non-volatile.

Summary of Contents for 90-30 PLC
































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 90-30 PLC

Cabletron Systems Netlink FRX8000 Installation And Setup Manual preview
Netlink FRX8000
Brand: Cabletron Systems Pages: 94
Cabletron Systems MMAC-Plus 9E423-24 Reference Manual preview
MMAC-Plus 9E423-24
Brand: Cabletron Systems Pages: 10
Cabletron Systems MMAC-Plus 9A128-01 Management Manual preview
MMAC-Plus 9A128-01
Brand: Cabletron Systems Pages: 22
Cabletron Systems Spectrum EMM-E6 Addendum Manual preview
Spectrum EMM-E6
Brand: Cabletron Systems Pages: 2
Cabletron Systems DLM6C-AA Overview And Setup Manual preview
DLM6C-AA
Brand: Cabletron Systems Pages: 54
Cabletron Systems Cabletron BRIM-F6 User Manual preview
Cabletron BRIM-F6
Brand: Cabletron Systems Pages: 43
Cabletron Systems Netlink FRX4000 Maintenance Manual preview
Netlink FRX4000
Brand: Cabletron Systems Pages: 60
Cabletron Systems 9E132-15 Appendix preview
9E132-15
Brand: Cabletron Systems Pages: 8
Cabletron Systems TRXI-22 Addendum preview
TRXI-22
Brand: Cabletron Systems Pages: 4
Hama 39707 Operating Instruction preview
39707
Brand: Hama Pages: 4
IEI Technology HPE-4S1 Quick Installation Manual preview
HPE-4S1
Brand: IEI Technology Pages: 3
Lochinvar Armor 101 Series Instructions Manual preview
Armor 101 Series
Brand: Lochinvar Pages: 28
Lochinvar Armor 101 Series Service Manual preview
Armor 101 Series
Brand: Lochinvar Pages: 44
Cisco MERAKI MX450 Installation Manual preview
MX450
Brand: Cisco MERAKI Pages: 4
Rane HAL1x System Installation Manual preview
HAL1x
Brand: Rane Pages: 128
Acard AEC-6885 User Manual preview
AEC-6885
Brand: Acard Pages: 34
Shure DFR22 Software Manual preview
DFR22
Brand: Shure Pages: 113
EZCast Pro Dongle II User Manual preview
Pro Dongle II
Brand: EZCast Pages: 24

Brands by name

Popular brands

Load more brands