GE Medical Systems MAC 1200 Operator'S Manual Download Page 90

Page: 90 / 180

6-4

MAC 1200

Revision B

2012250-022

Recording in 6 Lead Mode: Recording

Recording

127(

In 6 Lead mode, messages indicating disconnected electrodes are
also annotated on the recording, e.g. Lead fail C1.

After switching on the unit, press

to select 6 Lead mode.

Before recording the ECG, patient data can be entered (

). It is

recommended that you enter the patient’s name to annotate it on
every report.

Before initiating a recording, check the display for error messages (see
table below). Check all electrodes; if the message persists, there must
be a break in the patient cable. Replace the cable with a new one.

The recording is started and stopped with

Table 2. Messages Indicating Disconnected Electrodes

*RL*:

Right leg electrode disconnected

*RA*:

Right arm electrode disconnected

*LA*:

Left arm electrode disconnected

*LL*:

Left leg electrode disconnected

*V1*:

Chest electrode V1 disconnected

*V2*:

Chest electrode V2 disconnected

*V3*:

Chest electrode V3 disconnected

*V4*:

Chest electrode V4 disconnected

*V5*:

Chest electrode V5 disconnected

*V6*:

Chest electrode V6 disconnected

*RL*:

Right leg electrode disconnected

*RA*:

Right arm electrode disconnected

pat

info

Summary of Contents for MAC 1200





















































































































































































Search results

Summary of Contents for MAC 1200

Reviews:

GE Medical Systems MAC 1200, Operator'S Manual, Page: 90 / 180

Search results

Summary of Contents for MAC 1200

Reviews: