manualshive.com logo in svg

GE Medical Systems MAC 1200, Operator'S Manual, Page: 15 / 180

Share
Download
GE Medical Systems MAC 1200 Operator'S Manual Download Page 15

Revision B

MAC 1200

1-3

2012250-022

The Basics: About This Manual

About This Manual

Revision History

This manual has a revision letter, located at the bottom of each page. 
This revision letter changes whenever the manual is updated. Revision A 
is the initial release of the document. 

Manual Purpose

This manual describes the safe and effective operation of the MAC 1200 
unit. 

127(

This document describes the functionality of the U.S. interface for 
the MAC 1200 unit. 

Information in this manual differs from operating information for 
MAC 1200 units developed for use internationally. Please refer to PN 
2012250-021 for information on using the international interface. 

Revision

Date

Comments

A

31 March 2003

Initial release of manual, describes version 6.0.

B

21 July 2004

Revised CE compliance information, High Security 
“memory full” information added.

Summary of Contents for MAC 1200





















































































































































































Reviews:

No comments