manualshive.com logo in svg

GE Medical Systems MAC 1200, Operator'S Manual, Page: 41 / 180

Share
Download
GE Medical Systems MAC 1200 Operator'S Manual Download Page 41

Revision B

MAC 1200

3-9

2012250-022

Operating and Performance Tests: Connecting Peripheral Equipment

Connecting Peripheral Equipment

:$51,1*

SHOCK HAZARD — Strictly observe the following 
warnings. Failure to do so may endanger the lives of the 
patient, the user and bystanders.

‹

Connecting peripheral devices to the RS232 interface 
of the electrocardiograph creates a medical system. 
This system must meet the requirements of IEC 
60601-1-1.

‹

Use only the original GEMS IT connection cables.

‹

All non-medical devices of a system must be 
connected to the same electric circuit. Devices which 
are not connected to the same circuit must be 
electrically isolated (use isolated RS232 interface as 
per IEC 60601-1).

‹

A PC connected to the electrocardiograph should 
meet the requirements of EN 60601. If it doesn't, it 
must be set up outside the patient environment. If 
the PC fulfills the requirements of EN 60950, it must 
be set up within the medically used area, but outside 
the patient environment.

‹

Do NOT connect PCs to the electrocardiograph that 
fulfill neither EN 60601 nor EN 60950.

‹

Modems connected to the electrocardiograph must 
meet the requirements of EN 60950 or UL1950 (all 
modems recommended by GEMS IT meet these 
requirements). The specific regulations valid in your 
country must also be observed.

The modem must be set up within the medically used 
area, but outside the patient environment.

Summary of Contents for MAC 1200





















































































































































































Reviews:

No comments