GE Medical Systems MAC 1200 Operator'S Manual Download Page 115

Page: 115 / 180

Revision B

MAC 1200

9-9

2012250-022

System Setup: 6 Lead Mode

6 Lead Mode

Use the cursor keys to position the bar cursor on 6 Lead and confirm the

selection with

The configuration menu for the 6 Lead mode appears.

Report Sequence

[STANDARD] (l, II, III, aVR, aVL, aVF, VI, V2, V3, V4, V5, V6)

CABRERA (aVL, l, -aVR, II, aVF, III, VI, V2, V3, V4, V5, V6)

SEQ. NO. 4 (users can define a custom report sequence here):

Position the cursor on SEQ. NO. 4.

Press .

The display shown below will appear.

Press .

Report sequence

SEQ. NO. 4

Lead

Label

Chan. 1:
Chan. 2:
Chan. 3:
Chan. 4:
Chan. 5:
Chan. 6:
Chan. 7:
Chan. 8:
Chan. 9:
Chan. 10:
Chan. 11:
Chan. 12:

I
II
III
AVR
AVL
AVF
V1
V2
V3
V4
V5
V6

setup

Summary of Contents for MAC 1200





















































































































































































Search results

Summary of Contents for MAC 1200

Reviews:

GE Medical Systems MAC 1200, Operator'S Manual, Page: 115 / 180

Search results

Summary of Contents for MAC 1200

Reviews: