GDI Halo Product Manual Download Page 42

Page: 42 / 65

Inter-building

This is the Halo’s own brand of WDS mode. In this mode, the AP will automatically

connect to another Halo Radio which is set to inter-building mode, without manually

entering MAC address for each other. This creates a unique link to Halo radios only.

SSID

The SSID is the unique name shared among all devices in a wireless network. It is

case-sensitive, must not exceed 32 alphanumeric characters, and may be any keyboard

character. Make sure this setting is the same for all devices in your wireless network. The

default SSID name is wireless.

BSSID

A group of Wireless Stations and a single access point, all using the same ID (SSID),

form a Basic Service Set. Using the same SSID is essential. Devices with different SSIDs

are unable to communicate with each other. However, some access points allow

connections from wireless stations which have their SSID set to “any” or whose SSID is

blank (null).

Wireless Mode

Only 802.11 a is available.

Channel

This field identifies which operating frequency will be used. It should not be necessary to

change the wireless channel unless you notice interference problems or setting up the

AP near another access point.

Data Rate

Shows the available transmit data rate of the wireless network. The default is

Best.

Output Power

Set the transmit signal strength of the radio. The options are full, half, quarter, eighth, and

min. Decrease the transmit power if more than one AP is collocated using the same

channel frequency. The default is

Full.

Station Mode Flow Control

Uplink Speed Limit (1-1687): It indicates the transmission rate.

6-2 VAP / VLAN Settings

Overview

As the number of data-based systems increase, it becomes more and more difficult to

provide the network infrastructure (due to the sheer number of Ethernet connections that

need to be provided) from the perspective of cost, space, and wire management. The

Halo’s VLAN (Virtual Local Area Network) technology can help overcome this difficulty.

Now it is possible for these multi devices in function without the need for multiple physical

network APs. See the diagram below:

Summary of Contents for Halo


































































Search results

Summary of Contents for Halo

Reviews:

Related manuals for Halo

Brands by name

Popular brands

GDI Halo, Product Manual

Search results

Summary of Contents for Halo

Reviews:

Related manuals for Halo

Brands by name

Popular brands