manualshive.com logo in svg

GCS CYSCAN, Installation And Maintenance Manual, Page: 50 / 52

Share
Download
GCS CYSCAN Installation And Maintenance Manual Download Page 50

48

CyScan Positioning System • Installation and Maintenance Guide r1.1

GCS

GCS

Reflector Positioning Examples

These three pages provide examples of typical reflector layouts.

Example 1 - Ship on Tanker’s Port side, CyScan on ship’s Starboard side

B

1

2

3

A

Reflector Positions
1

A=0, B=0, orientation= 270

0

2
3

A=+52.52m, B=0, orientation= 270
A=+64.89m, B=0, orientation= 270

0

0

CyScan's Position

(NMEA-$RLS convention)

A   =
B

+29.559m

= -61.451m

Heading = 345

0

Notes:

1 The DP system will display the Origin of the A and B axes. This could be any

point on the tanker, the main mast, midway between perpendiculars or one of
the reflectors. In this example it is number 1 reflector.

2 The reflector numbering should be chosen so that they form an anti-clockwise

sequence when seen by CyScan.

This can be 1-2-3, or 2-3-1 or 3-1-2, etc.

3 In Auto Survey, target 1 would be the datum (primary target) and denotes the

origin of A/B frame.

Summary of Contents for CYSCAN





















































Reviews:

No comments