manualshive.com logo in svg

GCS CYSCAN, Installation And Maintenance Manual, Page: 38 / 52

Share
Download
GCS CYSCAN Installation And Maintenance Manual Download Page 38

36

CyScan Positioning System • Installation and Maintenance Guide r1.1

GCS

GCS

Appendix 5 - Recommended Spares List

Number

Name

Description

10-0003-4

CyScan Spares Kit 1

Includes grease gun, 10 fuses for PSU, 10 fuses for
CyScan Sensor, lens cleaning tissues.

21-0035-0

Baseplate Assembly

Baseplate, connectors, bellows, internal cables.

21-0034-0

Bottom Frame Assembly

Main frame of Sensor, universal joint.

21-0028-0

CyScan Motor Gearbox

Includes gearbox, motor, encoder, shaft and pcb’s.

22-0590-0

Rotor Heatshield

Fibreglass heatshield with name label.

21-0029-0

Actuator

Lead screw, stepper and drive pcb.

21-0027-0

CyScan Rotor

Scanner rotor including rotor and rangefinder
electronics.

21-0031-0

Body Cover Assembly

Main housing cover, including LEDs and handles.

39-0011-4

Yaw Gyro Assembly

Yaw gyro and pcb.

39-0003-2

VRU Assembly

VRU gyros, fluid sensor and pcb.

39-0010-2

CyScan Controller Module

Includes controller pcb, PC104 unit, ‘disk on chip’
and local interconnection cables.

98-0008-4

Silicone Grease

Waterproof silicone compound.

20-0030-0

CyScan PSU

Power supply unit and terminal box.

39-0005-2

RS485 Converter Module

Housed RS485 to RS232 converter module.

20-0031-0

2m Flat Reflector

2m x 350mm flat reflector including stainless steel
clamps.

20-0032-0

Cylindrical Reflector

1.5m cylindrical reflector including shackle.

38-0001-1

CyScan Console Notebook

User Console Notebook Computer.

33-0032-3

Programming Leads

Dual programming lead set for programming of
Sensor rotor and navigator.

Summary of Contents for CYSCAN





















































Reviews:

No comments