manualshive.com logo in svg

GCS CYSCAN, Installation And Maintenance Manual, Page: 15 / 52

Share
Download
GCS CYSCAN Installation And Maintenance Manual Download Page 15

13

CyScan Positioning System • Installation and Maintenance Guide r1.1

GCS

GCS

CyScan Removal

Decommissioning the CyScan system ready for stowage involves three basic stages:

• Switching off the CyScan Console System,

• Disconnecting the CyScan Sensor, and

• Un-mounting the CyScan Sensor

Switching off the CyScan Console System

!

Important:

 The system running the CyScan Console application MUST be

switched OFF before the CyScan Sensor is disconnected.

To exit CyScan Console and shutdown the system

1 Click the ‘CyScan’ button in the lower left corner of the screen (this button is

unavailable while navigating). The control dialog will be displayed:

2 Click the down-arrow to reveal the three options. Select ‘Shut down’ and click the

OK button.

3 Click ‘Yes’ to confirm your selection in the subsequent pop-up message. The

application will send shut down commands to the CyScan sensor and then close
itself down.

4 In the lower left hand corner of the Windows screen, click the 

Start

 button.

5 Select the 

Shut Down

 option.

6 In the subsequent 

Shut Down

 

Windows

 dialog, ensure that 

Shut Down

 option is

selected and click 

OK

.

7 When the system reports that it is 

‘safe to switch off your computer’

, turn off the

notebook computer.

You can now proceed to disconnect and un-mount the CyScan Sensor (if required).

The status LEDs on the sensor unit should show the yellow LED on and the green LED
flashing briefly once a second.

Note: The Console application should always be running when the Sensor is in
operation.

Summary of Contents for CYSCAN





















































Reviews:

No comments