manualshive.com logo in svg

GCS CYSCAN, Installation And Maintenance Manual, Page: 12 / 52

Share
Download
GCS CYSCAN Installation And Maintenance Manual Download Page 12

10

CyScan Positioning System • Installation and Maintenance Guide r1.1

GCS

GCS

The Data Converter

The Data Converter is necessary to translate between the RS485 signals used by the
CyScan sensor (and the DP system) and the RS232 signals used by the notebook compu-
ter. The Data Converter is contained within a watertight enclosure, however, it is usually
mounted on the bridge near to the CyScan notebook (refer to mounting template in
Appendix 4). The Data Converter requires a DC power supply between 7 and 35V – this
can be derived either from the CyScan Power Supply Unit or from the vessel’s bridge, as
required.

2TX

2RX

1TX

1RX

PWR

Signal

TX

NC

RX

NC

RTS

GND

7-35VDC

OV

Connector

1
2
3
4
5
6
7
8

Signal

GND

NC

RXB

RXA

TXB

TXA

Connector

6
5
4
3
2
1

DIP Switch

1
2
3
4

Position

OFF
OFF

ON

OFF

CyScan Notebook &

Power Connections

Console Signals

from PSU Unit

Data Converter Signal Crossover

The RS485 connection
between the CyScan PSU
and the Data Converter
requires a crossover in order
that transmit and receive
signals are correctly routed.
Ensure that the crossover is
correctly performed as the
cable from the Data Con-
verter is wired into the PSU.

RXA

TXB

TXA

RXB

GND

RXA

TXB

TXA

RXB

GND

CyScan

PSU

Data

Converter

The Data Converter is supplied with a single cable 2 metres in length that has a 9 pin
female D-Type connector for attachment to the CyScan notebook computer’s serial port.
A second cable gland allows entry for a cable to connect with the CyScan Power Supply
Unit.

Notebook computer

The CyScan notebook computer is supplied with a battery charger and mains plug. This
should be connected when in use. A footprint of 400 x 400 mm should be allowed for
the console notebook computer. The notebook charger is typically 200 x 70 x 50mm and
will require mounting close to a mains supply.

Summary of Contents for CYSCAN





















































Reviews:

No comments