GCC Technologies Jaguar II Series User Manual Download Page 50

Page: 50 / 72

Jaguar II User Manua

Connection

4-8

4.3 RS-232 Interface

Connecting to the RS-232 (Serial) Port

1. For IBM PC, PS/2 users or compatibles, connect the RS-232C cable to the serial connector

of the assigned serial port (COM1 or COM2) of your host computer.

2. Set up the communication parameters (Baud Rate and Data Bits/Parity) to match the

setting of software package, refer to chapter 3 – “Misc” key description.

Caution!! Please turn off the plotter before plugging the RS-232C cable.

4.4 Data Transmitting

There are two options to transmit the data from the computer to the cutting plotter:

Option 1:

With proper interface settings, the data can be transmitted from your application

software package to the cutting plotters directly.

Option 2:

Most cutting software packages are able to emulate HP-GL or HP-GL/2 commands,

therefore. As long as the file is HP-GL or HP-GL/2 format, the cutting plotter can

output the data precisely.

4.5 Printer Sever Shared Setting

In “A-PC”, set the printer driver as a shared printer, then use B-PC to connect A-PC’s printer

driver via internet.

A-PC

B-PC

Internet

USB COM Port

Summary of Contents for Jaguar II Series









































































Search results

Summary of Contents for Jaguar II Series

Reviews:

Related manuals for Jaguar II Series

Brands by name

Popular brands

GCC Technologies Jaguar II Series, User Manual

Search results

Summary of Contents for Jaguar II Series

Reviews:

Related manuals for Jaguar II Series

Brands by name

Popular brands