GCC Technologies Jaguar II Series User Manual Download Page 39 | Manualshive

Page: 39 / 72

background image

Jaguar II User Manual

The Control Panel 3-5

3.4 Menu Items

Below describes the functions of menu items

Menu or Key

Function

Setting

Default

Media sizing

Roll

To measure media width.

Maximum Tracking
150 meters

Edge

To measure media width and pull the media back till the front
paper sensor open.

Maximum Tracking
150 meters

Single

To measure media width and length.

Maximum Tracking
10 meters

[ SPEED ]

Speed

To set or modify tool speed at horizontal moving.

3~153cm/sec;
3cm/sec per step

72cm/sec

Up Speed

To set or modify tool speed at vertical moving.

3~153cm/sec;
3cm/sec per step

72cm/sec

Cutting Quality To set or modify cutting quality.

While cutting small letter, set as “Small letter”.
While cutting in high speed, set as “Draft”.
For normal operation, set as “Normal”.

Draft, Fair,
Normal, Fine,
Small Letter

Normal

[ FORCE ]

To set or modify the value of tool force.

For Jaguar II_61/101/132SC, when the cutting force exceeds
450g, the maximum cutting speed would be 15cm/sec and the
cutting quality would be Small Letter Mode (0.2g) and while
the cutting force is 300g-449g, the maximum cutting speed
would be 30 cm/sec and the cutting quality would be Fine
Mode (0.5g)

600gram;
5 gram/per step

80 gram

[ OFFSET ]

To set or modify the distance between the blade tip and the
center axis.

0.000~1.000mm 0.275mm

[ Arrow Keys ]

1. To move the tool carriage position on X or Y axis.
2. To select functions or change values of settings.

[ ENTER ]

1. The displayed parameters will be saved automatically.
2. To set a new origin at the present tool carriage position.

In “offline” mode, moving the tool carriage to desired
position by [Arrow Keys], then press [ENTER] key to set a
new origin. While moving with the parameters of XY-axes
displayed, press [MISC] key will enable fine-tune
movement; press [MISC] key again to disable the function.

[ PAUSE/RESUME ]

To temporarily halt the cutting process.
To resume the process by press [Pause/Resume] key again.

[ ONLINE/OFFLINE ]

1. To switch between online mode and offline mode.
2. To stop the cutting job or abort the change of setting.

Once press this key, the cutting job will be terminated
immediately and cannot be resumed.

[ DATA CLEAR ]

«
...
37
38
39
40
41
...
»

Summary of Contents for Jaguar II Series









































































Reviews:

No comments

Related manuals for Jaguar II Series

Brand: Roland Pages: 144

Brand: GCC Technologies Pages: 76

Brand: GCC Technologies Pages: 179

Stylus Pro 7400

Brand: Epson Pages: 12

Stylus Pro 10000 Series

Brand: Epson Pages: 6

Brand: USCutter Pages: 63

Brand: plottiX Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands