manualshive.com logo in svg

GCC Technologies Jaguar II Series, User Manual

Introducing the GCC Technologies Jaguar II Series user manual - your go-to resource for complete guidance and optimal performance. Our comprehensive manual is available for free download from manualshive.com, ensuring easy access to step-by-step instructions, troubleshooting tips, and invaluable insights to enhance your Jaguar II experience.

Share
Download
background image

                                                                                                                    Jaguar II User Manual 

 

The Control Panel                                                                          3-7 

   

previous origin while the selection of “Disable” allows the 
carriage to do so. 

Set 

Communication

 

To build up the communication between host computer and 
cutter.   
Baud Rate is to determine the speed of data transmission.   
Data Bits refers to the size of one block of data. 
Parity is used to check if data was revived correctly or not. 

 

9600, n, 7, 1, p  

9600pbs, 7 Bits with NO Parity 

9600, o, 7, 1, p  

9600pbs, 7 Bits with ODD Parity 

9600, e, 7, 1, p  

9600pbs, 7 Bits with EVEN Parity 

9600, n, 8, 1, p  

9600pbs, 8 Bits with NO Parity 

9600, o, 8, 1, p  

9600pbs, 8 Bits with ODD Parity 

9600, e, 8, 1, p  

9600pbs, 8 Bits with EVEN Parity 

19200, n, 7, 1, p 

19200pbs, 7 Bits with NO Parity 

19200, o, 7, 1, p 

19200pbs, 7 Bits with ODD Parity 

19200, e, 7, 1, p 

19200pbs, 7 Bits with EVEN Parity 

19200, n, 8, 1, p 

19200pbs, 8 Bits with NO Parity 

19200, o, 8, 1, p 

19200pbs, 8 Bits with ODD Parity 

19200, e, 8, 1, p 

19200pbs, 8 Bits with EVEN Parity 

 

 

Firmware 
Version 

To display the version number of Firmware and FPGA code. 

 

 

 

 

Paper Saving 
Mode 

To save media by four different modes:                                                                             
1. Length expanded mode      2. Width expanded mode                                                                                                                     
3. Both expanded mode          4. Both unexpanded mode 

 

 

Both 

unexpanded

 

mode 

Select 
Language 

  To select displayed languages on LCM panel in English and 

Chinese 

English 
Chinese 

English 

Select Units 

Provide four-unit systems for users convenient. 

cm/gram; inch/oz; 
cm/oz; inch/gram 

Metric 

Image Scale 
Length 

Image Scale 
Width 

To adjust the image scale of media length and width that may 
cause by the thickness of the media.     

 

The Numerator is the ideal length, and the Denominator is 

the actual length measured from the resultant.   

 

For example, cutting a line with 500.0 mm length. The 

procedure as follows:                                                                     
1. Press the [LEFT ARROW] to choose the Numerator and     

select 500.0 mm,                                                       

2. Cut the length by sending a graph file,                 
3. Measure the length then use the [RIGHT ARROW] key to   

choose the Denominator, then         

4. Press [UP ARROW /DOWN ARROW] to change the 

values of the actual length. 

 

500/500 
mm 

Scale Length 

Scale Width 

Fixed scaling, for maintenance only. 

 

 

[ CUT TEST ] 

Square Cut 

To perform a cutting test at present blade position.                                                                                                                               
For more information, please refer to “2.7 Adjusting the 
Cutting Force and Offset” to adjust blade force and cutting 
speed. 

 

 

 

 

Repeat Last 
Plot 

Recut: 
To repeat the last job without re-sending the data.                                                                                                                                                             

1~99; 
1 per step 

 

Summary of Contents for Jaguar II Series









































































Reviews:

No comments

Related manuals for Jaguar II Series

Brands by name

Popular brands

Load more brands