GCC Technologies Jaguar II Series User Manual Download Page 43

Page: 43 / 72

Jaguar II User Manua

Connection

4-1

The cutting plotter communicates with a computer through a USB (Universal Serial Bus) or a

Serial port (RS-232C). This chapter shows you how to connect the cutting plotter to a host

computer and how to set up the computer/cutting plotter interconnection.

Notice:

When USB connection is enabled, serial port will be disabled automatically.

4.1 USB Interface

Jaguar II build-in USB interface are based on the Universal Serial Bus Specifications Revision

1.1. (Operation system of Windows 95, Windows NT don’t support USB).

USB driver installation

Use the USB One-click Installation for quick driver installation. Follow the simple steps

below for driver setup.

Step 1:

4. Connection

Caution!!

If you are using Windows 8/ 7/ Vista/ XP/ 2000 as your

operating system, make sure you log in using the

“Administrator” account.

Serial Interface Connector (RS232C) – used to

connect the cutting plotter to a computer

through a serial interface cable.

USB Connector

–

used to connect the cutting

plotter to a computer through a USB cable.

Summary of Contents for Jaguar II Series









































































Search results

Summary of Contents for Jaguar II Series

Reviews:

Related manuals for Jaguar II Series

Brands by name

Popular brands

GCC Technologies Jaguar II Series, User Manual

Search results

Summary of Contents for Jaguar II Series

Reviews:

Related manuals for Jaguar II Series

Brands by name

Popular brands