background image

8

Blue light

WARNING

Health hazard due to LED light with high blue content

Recent studies show that light with a high blue content can lead to permanent retinal damage or contribute to it. 
White LED light also has a high blue content. Users should therefore avoid prolonged visual contact with white  
or blue LED light.

• 

The scanner emits white light or blue light with each measurement.  
Cover the scanner during operation.

• 

Wearers of glasses can protect their eyes with glasses with a blue light filter.

Falling

CAUTION
Risk of falling due to packaging materials

The scanner is extensively packaged for protection against transport damages. The packaging can be an obstacle 
during setup and can cause falls.

• 

Do not leave packaging materials lying on the ground.

• 

Before transporting, move all obstacles out of the way.

Carrying

CAUTION
Risk of injury due to incorrect carrying

Due to its size and weight, we recommend that two people should unpack and set up the scanner. In particular, 
shorter individuals can be injured if they lift or carry the scanner by themselves without any help.

• 

Two people should lift the scanner out of its packaging.

• 

Two people should carry the scanner.

• 

To transport the scanner, always grasp it by the bottom corners.

Crushing

CAUTION
Risk of injury due to the mechanical parts of the scanner

You can get crushed by the mechanical parts of the scanner.

• 

Only put your hands inside the scanner when the axes have stopped. Should the axes not stop at the end of  
a scanning process, turn off the scanner and disconnect the power plug.

Entanglement

CAUTION
Injury due to entanglement of clothing, jewelry or hair

Loose clothing, jewelry or long hair can get entangled in the mechanical parts of the scanner. Due to motion, objects 
and hair can get entangled inside the scanner. This can lead to injury.

• 

Do not wear any loose garments such as shawls and ties, or jewelry like long necklaces, at the scanner’s workplace.

• 

Comb your hair into a firm pigtail, for example.

• 

However, should a piece of clothing, hair or jewelry get entangled among the moving parts of the device, turn the 
scanner off immediately. Disconnect the power plug before removing the entangled part.

Summary of Contents for Aadva Lab Scanner 2

























































Reviews: