GBD BE24G, Installation Instructions Manual

Page: 26 / 60

26
UK
BE24G
Description Position Value Type
7 - PROTECTION FUSES
15A F F1
Protects the circuit board.
15A
F F2
Protects battery power circuit.
3,15A F F3
Protects external accessories, electric lock and flashing light.
8 - WARNING LEDs
Description
Position Colour
Signal
L1 GREEN START
Comes on when the START control is activated from the terminal board or the receiver.
L2 GREEN PED
Comes on when the PED control is activated from the terminal board or the receiver.
L3 RED PHOTO1
Always on. Comes off when the contact of terminal PHOTO 1 is opened.
L4 RED PHOTO2
Always on. Comes off when the contact of terminal PHOTO 2 is opened.
L5
RED SAFETY
Always on. Comes off when the resistance value of terminal SAFETY is wrong.
L6 RED IN1
Lights when the contact switch from open to close and remain on until the contact
switch off
The control board is locked, it’s necessary to execute a new travel
learning procedure.
The control board is in pre-learning phase, after pressing MEMO
button.
During sleep time, the control board is set to work with GROUND
operator.
2A T F4
Protects the transformer.
Motor 1 encoder error, travel learning procedure failed.
Motor 2 encoder error, travel learning procedure failed.
M5
M6
26 COM
27 ANT
+Battery 24V MAX 3Ah. 28 +BAT
-Battery 24V MAX 3Ah. 29 -BAT
Antenna braid input.
Antenna signal input.
L8 BLUE INFO
0,2s ON 0,2 OFF
30s ON
0,2s ON-4s OFF
1s OFF - 0,6s ON - 1s OFF
X2
1s OFF - 0,6s ON - 0,6s OFF
0,6s ON - 1s OFF
X2
27
BE24G
UK
Description DIP Status Function
9 - DIP SWITCH DIP1
OFF
STEP-BY-STEP
WITH STOP
AUTOMATIC
OFF
1_1
1_2
1_3
1_4
ANTI CRUSHING
SENSITIVITY
Very High sensitivity.
OFF
OFF
High sensitivity.
OFF
ON
Medium sensitivity.
ON
OFF
Low sensitivity.
ON
ON
The settings are stored during the rest phase (gate closed).
The default settings are highlighted in the boxes with grey background.
1_5
TOTAL
AUTOMATIC
RECLOSURE
Total automatic reclosure disabled. OFF
Enable the automatic closure or after the pause time set by default 20s
or after the pause time learned.
ON
1_6
AUTOMATIC
PEDESTRIAN
RECLOSURE
Automatic pedestrian reclosure disabled.
OFF
ON
Enable the automatic closure or after the pause time set by default 10s
or after the pause time learned.
ON
Operation in response to the START command:
Ÿ Gate closed OPENS →
Ÿ
During opening STOPS
→
Ÿ
Gate open CLOSES
→
Ÿ
During closing STOPS
→
Ÿ
After a STOP Inverts the motion
→
Operation in response to the START command:
Ÿ Gate closed OPENS
→
Ÿ During opening UNINFLUENTIAL
→
Ÿ Gate open Reloads the automatic closing time if automatic closing →
is enabled, otherwise it closes.
Ÿ
During closing OPENS
→
ON
Operation :
Ÿ
Gate closed UNINFLUENTIAL
→
Ÿ
During opening STOP
→
Ÿ
Gate open STOP, no automatic reclosing
→
Ÿ
During closing STOP
→
Ÿ
After a STOP Reverses the motion
→
Operation
Ÿ
Ÿ During opening Immediate motion inversion for 1s at low speed,. →
Ÿ Gate open UNINFLUENTIAL →
Ÿ
During closing Immediate motion inversion for 1s at low speed.
→
:
Gate closed UNINFLUENTIAL →
TERMINAL 21
AS EDGE
TERMINAL 21
AS STOP
L7 RED RX
Always off, comes on when P2 button is pressed.
L9
Always on. It shows logic circuit power supply
GREEN VCC