GBD BE24G, Installation Instructions Manual

Page: 24 / 60

24
UK
BE24G
WARNING: IMPORTANT SAFETY INSTRUCTIONS.
It is important for the safety of persons to follow these instructions.
Keep this instruction manual.
3 - INSTALLATION WARNINGS
4 - WARNINGS FOR THE USER
• In the event of an operating fault or failure, cut the power upstream of the control unit and call
Technical Service. Periodically check functioning of the safety devices. Any repairs must be carried out by
specialised personnel using original and certified materials.
• The product may not be used by children or persons with reduced physical, sensorial or mental capacities,
or lacking experience and knowledge, unless appropriately instructed.
• Do not access the circuit board for adjustments and/or maintenance.
• Before proceeding with installation, fit a differential magnetothermal switch with a maximum capacity of 10A
upstream of the system. The switch must guarantee omnipolar separation of the contacts with an opening
distance of at least 3mm.
To prevent possible interference, differentiate and always keep the power cables (minimum cross-section
1.5 mm²) separate from the signal cables (minimum cross-section 0.5 mm²).
Make the connections referring to the following tables and to the attached screen-print. Be extremely careful to
connect in series all the devices that are connected to the same N.C. (normally closed) input, and in parallel all
the devices that share the same N.O. (normally open) input.
Incorrect installation or improper use of the product may compromise system safety.
Keep all the materials contained in the packaging away from children since they pose a potential hazard.
The manufacturer declines all responsibility for improper functioning of the automated device if the original
components and accessories suitable for the specific application are not used.
When installation is complete, always carefully check proper functioning of the system and the devices used.
This instruction manual addresses professionals qualified to install “live equipment” and therefore requires
good technical knowledge and installation in compliance with the regulations in force.
Maintenance must be carried out by qualified personnel.
Before carrying out any cleaning or maintenance operation, disconnect the control unit from the mains.
The control unit described in this document may only be used for the purpose for which it was designed.
Check the intended end use and take all the necessary safety precautions.
Use of the products for purposes different from the intended use has not been tested by the manufacturer and
is therefore on full responsibility of the installer.
Mark the automated device with visible warning plates.
Warn the user that children or animals should not play or stand near the gate.
Appropriately protect the dangerous points (for example, using a sensitive frame).
•
•
•
•
•
•
•
•
•
•
•
•
•
•
5 - ELECTRICAL CONNECTIONS: CONNECTORS
Description
CF1 0 VAC from transformer
FASTON
24 VAC from transformer CF2
25
UK
BE24G
6 - ELECTRICAL CONNECTIONS: TERMINAL BOARDS
Description Terminal Position Signal
M1
Motor 1+ 1 M1+
Motor 1- 2 M1-
Motor 2+ 3 M2+
Motor 2- 4 M2-
+ 12V Electric lock power supply MAX 15W.
5 EL+
- Electric lock power supply 12V MAX 15W.
6 EL-
+ FLASHLIGHT power supply 24 VDC MAX 10W.
7 LAMP/SPIA
- FLASHLIGHT power supply 24 VDC MAX 10W.
8 LAMP/SPIA
M3
+24Vdc MAX 10W External accessory power supply
9 +ACC
External accessory power supply common
10 -ACC
Motor 1 E5VDC power supply.
11 5V
Motor 1 ENCODER signal.
12 S1
Motor 1 ENCODER power and signal common.
13 COM
Motor 2 E5VDC power supply.
14 5V
Motor 2 ENCODER signal.
15 S2
Motor 2 ENCODER power and signal common.
16 COM
M4
START input (N.O.).
17 START
PEDESTRIAN input (N.O.)
The Pedestrian manoeuvre is carried out with Automatic logic, not modifiable.
18 PED
19 PHOTO 1
20 PHOTO 2
21
Accessory common. 22 COM
23
Accessory common.
COM
PHOTOCELL 1 input (N.C.). Input active only during closing.
It stops and inverts the motion, opening the gate completely. If the gate is closed, it does
not affect its functioning. If intercepted during pause, it reloads the pause time.
If not used, make a jumper with terminal no. 22.
M2
PHOTOCELL 2 input (N.C.). Input active during both opening and closing.
If intercepted, it immediately stops the motion and holds it stopped until the photocell
is freed. Upon release, motion always restarts in opening. If intercepted during pause,
it reloads the pause time.
If not used, make a jumper with terminal no. 22.
STOP
SAFETY
Programmable INPUT (STOP – EDGE). If not used, make a jumper with terminal no. 22.
24
Unused imput. 25 IN2
IN1
Input IN1 (N.O.) fo .
Operation:
Gate closed total opening
→
During total opening IRRELEVANT
→
During pedestrian opening total opening
→
Gate completely open recharge the automatic closing time, if enabled,
→
otherwise IRRELEVANT
Gate open form Pedestrian total opening
→
During closing total opening
→
WARNING: remember to enable both the automatic reclosure, if you want, and the
condominium logic, if you do not want any interaction with START command during
the opening phase.
r the connection of external devices, for instance clock