![background image](http://html1.mh-extra.com/html/gbc/talon-44-ce/talon-44-ce_installation-and-operation-manual_4077073022.webp)
Operations Manual
Page 22
©2004 General Binding Corporation
T
ALON
44/64
CE
R. REAR TABLE:
(Figure 20) Provides a working surface
when operating the machine from the rear. This table may also
be lowered when webbing for roll to roll applications.
To lower, slide the left and right side rear table latches (1)
to the unlatched position and lower the rear table.
S. REAR SLITTER:
(Figure 20) Used to cut the film web
where it exits the rear of the laminator.
To make a cut, push down on the blade engage lever (2)
and slide to the opposite side.
T. FILM WEB:
Laminating film loaded into the machine.
U. NIP POINT:
The point at which the top and bottom
rollers come into contact. The Nip Point of the heat rollers
is the place at which the items for lamination are introduced
into the laminator.
V. FOOTSWITCH:
To operate using the footswitch, there
are a number of factors that determine how the machine
runs based on the position of the key on the Hand – Foot-
switch Control and if the safety shields are in place or not.
Refer to the chart below for settings and speeds.
Selector key
position
Safety shield on
(Latch locked)
Safety shield off
(Latch Unlocked)
Clockwise
Foot –Pedal:
Limited speed of 3f/m or
1m/m
Foot –Pedal:
Limited speed of 3f/m or
1m/m.
Control panel run switch:
Limited speed of 3f/m or
1m/m.
Control panel run switch:
Limited speed of 3f/m or
1m/m.
Counter
Clockwise
Foot –Pedal: Up to Max
Foot –Pedal: No function.
Control panel run switch: Up
to Max. speed.
Control panel run switch: No
function.
Selector key
removed
(Key removed
when turned
counterclockwise)
Foot –Pedal:
Up to Max speed.
Foot –Pedal:
No function.
Control panel run switch: Up
to Max. speed.
Control panel run switch: No
function.
W. PRINT UNWIND BASKET:
(Figure 21) Holds a rolled
image. Prevents the image from touching the floor.
X. SEPARATOR BAR OPTION:
(Figure 20) Required if
running Accushield® material.
(Talon 44 Part # 2020580)
(Talon 64 Part # 2020579)
To install, replace the rear slitter with the separator bar.
Y. REWIND KIT OPTION:
Enables roll to roll webbing
of material. This kit must be installed by a qualified GBC
service representative.
(Talon 44 Part # 1715822)
(Talon 64 Part # 1715823)
Fig 19
(2)
(1)
(S)
(R)
(X) - Option
Fig 20
(W)
(V)
Fig 21
Option
Summary of Contents for Talon 44 CE
