![background image](http://html1.mh-extra.com/html/gbc/oorca-iii/oorca-iii_operation-manual_571021017.webp)
Installation
ORCA-III Operation Manual
GBC Pro-Tech 1997 October
2-6
7.
Adjust the air cylinder rate. (See Section 4:
Maintenance and Troubleshooting for the
procedure.)
8.
Replace both cabinet covers.
/HYHOLQJ
Tools required:
•
Adjustable wrench
•
Carpenter's level
To level the laminator:
1.
Raise each end, remove the castors and install a
leveling pad and stud onto each of the foot
brackets at the four bottom corners of the
laminator. Thread third nut on stud above foot
bracket.
WARNING
Do not lift the wheels more than 3/4" (2 cm.)
above the floor. The leveling pads can become
unstable. You can be crushed.
2.
Thread stud into 4 leveling pads lock down with
nut. Thread second nut onto stud.
3.
Place a carpenter's level front to rear across the
two lower tie bars at one end of the machine .
4.
Level this end of the machine front to rear,
raising or lowering the leveling pads by adjusting
the middle nuts on the foot bolts.
5.
Move the level to the other end of the machine
and level front to rear.
6.
Place the level directly on one of the tie bars and
level the machine side to side.
7.
Recheck the front to rear level condition to insure
that it has not changed. If it has, repeat the
leveling procedure.
8.
When all the measurements indicate that the
machine is level, tighten down the top nuts on the
foot brackets to lock the pads in their current
position.
6WDUWXS
The first time the laminator is started and every time
it is serviced you should use the following checklist to
confirm that the unit is operating properly and that all
safety mechanisms are functioning.
Startup Checklist
Start the laminator and go through the following
checklist.
❒
Are the emergency stop buttons working?
Push down on one of the emergency stop buttons.
The laminator should stop. Pull up on the button
and push the reset button on the lower back of
the laminator. The laminator should resume
operation. Always check all four buttons.
WARNING
Never operate the laminator unless both of the
emergency stop buttons are functioning
properly. You can be crushed or burned.
❒
Is the photoelectric eye system working?
With the laminator running and the rolls in the
“up” position, place an object approximately the
size of your hand just in front of the nip on both
the front and back of the laminator to confirm
that the photoelectric eye system is functioning.
The
roll
s should stop. Move the object away from
the nip. The laminator should resume operation if
the machine is in “footswitch” mode. If the
machine is in “run” mode, it should be necessary
to push the FORWARD or REVERSE button
to resume roll motion.
WARNING
Never operate the laminator unless the
photoelectric eye system is functioning
properly. You can be crushed or burned.
Summary of Contents for OORCA-III
