![background image](http://html1.mh-extra.com/html/gbc/oorca-iii/oorca-iii_operation-manual_571021058.webp)
ORCA-III Operation Manual
Maintenance and Troubleshooting
GBC Pro-Tech 1997 October
4-1
6HFWLRQ
0DLQWHQDQFH DQG
7URXEOHVKRRWLQJ
GBC Pro-Tech laminators require minimal
maintenance. However, regular maintenance is
essential to keep any piece of precision machinery at
peak performance. A maintenance schedule and a
section of procedures are included in this section.
Table 4-1:
Maintenance Schedule
Daily
•
Clean the rolls
•
Inspect the electrical cord for
damage
•
Inspect the footswitch cord for
damage
Monthly
•
Adjust the nip, if needed
•
Check the chain tension
•
Inspect the area around the
laminator for possible hazards (dust
buildup, combustible items stored
too close, etc.)
•
Adjust the air cylinder rates, if
needed
Every
Six
Months
•
Lubricate the grease fittings and
chain
•
Check wire termination tightness
&OHDQLQJ
Tools required:
•
Adhesive coated board
•
80% (or stronger) isopropyl alcohol (or
dishwashing detergent)
•
Rubber cement eraser (optional)
•
Several 100% cotton terry cloths
•
Protective rubber gloves
To clean the laminator rolls:
WARNING
Exercise extreme caution while cleaning the
laminator. You can be caught in the turning
rolls and crushed or burned.
1.
While the laminator is at normal operating
temperature, put on the rubber gloves and, using
a rubber cement eraser, remove any heat
activated adhesive from the rolls. Run the main
rolls in reverse and the pull rolls in forward to
clean. Use the footswitch to rotate the rolls for
cleaning.
CAUTION
If running Scotchprint material, clean all the
release liner residue off the bottom roll
IMMEDIATELY. The residue hardens and
ruins the roll.
CAUTION
Do NOT pick or pull heat activated adhesive
off the rolls when they are cold. You can cause
irreparable damage to the laminating rolls.
To clean beads of adhesive, dust and dirt from the
rolls:
1.
Allow the laminator to cool slightly to no higher
than 110 ºF (43 ºC).
2.
Set the FWD/REV switch to the REV position.
3.
Clean the rolls using a moderate amount of 80%
(or stronger) isopropyl alcohol on a cotton terry
cloth.
Summary of Contents for OORCA-III
