- 14 -
•
Mount Alarm button in drivers switch panel.
•
Ensure SD card is installed in DVR control unit prior to turning on the system.
•
Connect portable monitor, (VRIPLLMD-6708Y), to DVR with cable to aim camera and
program NiTRO
400 or NiTRO-X
400.
Alarm Button Mounting
Alarm Button Mounting
Alarm Button Mounting
Alarm Button Mounting
The Alarm Button is generally mounted in a location that is within reach of the driver where
the drivers hand will naturally fall into place and its recommended location is towards the
front of the left switch panel.
Red lead (X) is connected to bus power,
switched 12V (Key On / Off), e.g. Ignition
Source.
Black lead (Y) is connected to the Green (D)
lead from CAB000218, See Figure 2.
Record LED
Record LED
Record LED
Record LED Mounting
Mounting
Mounting
Mounting
The Record LED is generally mounted in a location that is within line of sight of the driver.
Red lead (W) is connected to bus power,
switched 12V (Key On / Off), e.g. Ignition
Source.
White lead (V) is connected to the Yellow
lead (E) from CAB000218, See Figure 2.
CAB000219 (4 PIN; NiTRO
CAB000219 (4 PIN; NiTRO
CAB000219 (4 PIN; NiTRO
CAB000219 (4 PIN; NiTRO
) / CAB000262 (6 PIN; NiTRO
) / CAB000262 (6 PIN; NiTRO
) / CAB000262 (6 PIN; NiTRO
) / CAB000262 (6 PIN; NiTRO----X
X
X
X
) POWER CABLE
) POWER CABLE
) POWER CABLE
) POWER CABLE....
CAB00219 (4 PIN)
NiTRO
DVR Power
Cable (30 feet long).
See Table 2 for
Definitions and Figure
2 for Connections.
- 55 -
OTHER
OTHER
OTHER
OTHER
CONFIGURATIONS
CONFIGURATIONS
CONFIGURATIONS
CONFIGURATIONS....
CAMERA ADAPTER CABLES
CAMERA ADAPTER CABLES
CAMERA ADAPTER CABLES
CAMERA ADAPTER CABLES....
1 CAMERA:
CAB000209
2 CAMERAS:
CAB000202
3 CAMERAS:
CAB000202 AND CAB000209
4 CAMERAS:
2 X CAB000202
•
Constant 12 volt power must be provided to the NiTRO™. The preferred connection is at
the main bus battery(s), with an alternate connection source at the 12V terminal in the
electrical panel which is supplied power from the battery with a 4 gauge wire or thicker.
•
This source must maintain a minimum of 8V during engine cranking.
•
The 12V+ side of the constant power connection (CAB000211) must be fused at the
power source with the fuse provided.
•
If main harness extension is required, use only 16 AWG or thicker wire.
•
Main ground needs to be connected to a solid chassis ground, preferably the negative
post at the battery, if not possible and grounded in the electrical panel, a shake-proof or
lock washer is required in the head of the bolt. Scrap away any paint to ensure a clean
connection.
CAB000
CAB000
CAB000
CAB000268 4 PIN Power Connector to 6 PIN Power Connector Adapter.
268 4 PIN Power Connector to 6 PIN Power Connector Adapter.
268 4 PIN Power Connector to 6 PIN Power Connector Adapter.
268 4 PIN Power Connector to 6 PIN Power Connector Adapter.
Please Note:
Please Note:
Please Note:
Please Note: CAB000268 only applies to the connection of a NiTRO-X
to the existing
cabling of a NiTRO
. This adapter cable allows all the currently installed cabling to be utilized.
