background image

                                                                                                Page 7    /    19 

Caution: Keep the fire box clean, before you start the stove. 

 

 

A

UTOMATIC

   

S

AFETY

   

F

EATURES

:

 

 
Your pellet Stove has the following safety features: 

A.  The    stove    will    shut    off    when    the    fire    goes    out    and    the    exhaust   

temperature    drops    below    120°F(52°C). 

B. The stove has a high temperature safety switch. If the temperature on the hopper reaches 
200°F 
(93°C),  the  auger  will  automatically  stop  and  the  stove  will  shut  down  when  the  exhaust 
temperature cools.    If this happens, call your local dealer to reset the 200°F (93°C) high limit 
switch. 

ALSO

 

FIND

 

THE

 

REASONS

 

WHY

 

THE

 

UNIT

 

OVERHEATED.

 

C. If the power goes out, the unit will stop running.    When the power comes back on, the stove 

will not restart unless the exhaust temperature is still above 120°F (52 °C). 

 

Product performance   

The  pellet  stove  has  an  advanced  designed  and  has  individual  fresh  air  input  and  venting 
system.  Negative  pressure  burning  technology  causes  high  efficiency  and  little  ash  outlet 
during burning. It will be shut off automatically by wrong burning or if out of fuel. Large heat 
output, quick heating and low fuel cost are its advantages.       
 

1.

 

Main performance   

Model 

    HP24 

Rating input                                  BTU/h 

30000BTU/H(9.4KW/HOUR) 

Rating fuel consumption            kg/h 

1.6 +_5% 

Heating area                                m

²

 

~120 

Rating voltage                              V 

230 

Rating frequency                          Hz 

50 

Maximum power requirement    W 

375 

Hopper                                            kg 

20 

Venting pipe diameter                mm 

80 

Air input pipe diameter              mm 

50 

Unit size (wide* depth*high)    mm 

650*600*1000 

 

2.

 

  Wood pellet 

This stove uses wood pellet fuel. It is small column pellet with cleaning surface. The diameter 
is ¢6-8mm, the length is no more than 35mm, and its humidity is no more than 10%. Ash is no 
more than 1%. 
 

Summary of Contents for HP24




















Reviews: