background image

MDE-4813D CFN PLUS Installation Manual

 · 

February 2018

 

48 

3-8.3. Mechanical Pump - Required Connections   

This paragraph describes the required wiring connections between the mechanical pump and the 
CFN PLUS

Figure 3-13

 and show a schematic diagram of the connections between the CFN PLUS 

and the mechanical pump components. 

Figure 3-15

 shows a detailed wiring diagram between the 

CFN PLUS terminal block and the pump components.   

Pulse Input Wires:  

The dispenser outputs pulses to the system by means of the Pulser unit, 
installed inside the pump head. The Pulse rate per volume (liter/gallon) 
is determined by the Pulser unit. It is programmed as a “factor” by the 
Head Office controller.   

Handle Status Input 
Wires:  

The handle signal is used to signal the system that the pump is “In Use” 
mode. When the dispenser handle is lifted this contact will close. This 
should signal the system that the pump is “In Use” or that the 
transaction ended.  

Authorization Output 
Wires: 

The dispenser requires an authorization signal from the CFN PLUS to 
start a sale transaction. Without this authorization signal, the electric 
valve (or pump) will not open and the sale transaction will not begin. 
The CFN PLUS sends the authorization signal in the form of an AC 
power signal to the valve. When the dispenser receives the authorization 
signal, fuel is flow. 

 

Summary of Contents for ORPAK CFN PLUS



























































































Reviews: