![background image](http://html1.mh-extra.com/html/garland/mwe-9501/mwe-9501_operation-manual_564375019.webp)
The Master Power (Pushbutton (ON / OFF)
Program Mode Button - Two Functions
Indicator Lights
Right Arrow Button - Two Functions
Up Arrow Button - Two Functions
Controls power to the grill and must be turned "ON" to start
the operation. The controller displays will be active
when the switch is "ON".
There are four, (4), indicator lights, indicating the temperature
status of each zone on the grill, one, (1), on the upper platen,
(top light), and three, (3), on the lower, (lower section of
lights, top to bottom; rear, center, front, respectively - see
diagram on previous page). Each light can display three,
(3), different colors, indicating temperature status for the
corresponding zone.
Red:
The zone(s) is too hot (more than 79ºF/43ºC over
the set temperature) or heat zone(s) failure.
Amber: The zone(s) is calling for heat.
Green: The zone(s) is at or above the set temperature
(maximum of 79ºF/43ºC).
Display:
The controller display will contain information relevant to
each operation in both cook and program modes.
NOTE: ** Version 7.3X EPROM Chip ** - At the end of the
pre-programmed menu item Round Eggs cook cycle, the rear
LED (Gas Zone) will turn off for a period of 60 seconds. The
LED (or heat) will remain off for the period of 60 seconds
unless another cook cycle is initiated.
1) In the cook mode, when depressed, it will display the
Remove time, Top Temperature, Bottom temperature and
Gap setting for the menu item displayed. Each item will
be displayed in the order as stated above. After 5 seconds
the display will return to the product menu item.
1) In the program mode various displayed parameters will
be shown in numerical values. Each number, when
displayed, will have a flashing digit...the cursor digit.
The "RIGHT ARROW" button will move the cursor to
the next digit. Using the "RIGHT ARROW" button in
conjunction with the "UP ARROW" button described
above, any parameter value displayed in the program
mode may be altered.
2) In the cook mode it will scroll backward through the menu
items.
1) The primary function is to access Programming and
Calibration of the grill. Push and hold for five (5)
seconds. Display will show type and version number.
There are two programming features,
"MENU ITEMS" and "SYSTEM SETUP".
2) The second function is when used with "TEMP" button.
To display all temperature zones at the same time, press
the "TEMP" button one time and the 'PROG" button
five (5) times. This will display all four (4) temperature
zones.
The grill control will allow for 2 functions, both described in
the following sections.
The “
Normal Operating Mode
”, also known as the Cook
Mode is the mode in which is used during normal cooking.
In the normal operating mode, the operator can start a cook
cycle, cancel a cook cycle, view actual temperatures, view
settings for the currently selected menu item, scroll to
another menu item (Both forward and backward), and enter
the “
Programming Mode
”.
The “
Programming Mode
” is the mode in which the grill
operator, manager, or service technician can change various
programmed features to specific menu items, or change
features that would apply to the entire grill.
General Overview
DESCRIPTION OF GRILL CONTROLS
Menu Button - Two Functions
1) In the cook mode this button will allow you to change
menu items.
2) In the programming mode, the button is used to advance
to the next program item.
Temperature / Function Button - Two Functions
1) In the Cook mode, each time the button is pressed the
current temperature for one zone will be displayed. The
displayed temperature begins at the upper platen and
works sequentially to the front each time you press the
button. After five (5) seconds the display will return to
the menu item selected.
2) In the Program mode, this button becomes the Function
button allowing you to scroll through the functions in the
"MENU ITEMS" section of programming.
2) In the program mode, it will change the value of the
current cursor digit, (see "RIGHT ARROW" button).
Summary of Contents for MWE-9501
