English
32/132
English
33/132
6.2.7. CHANGING THE NYLON WIRE
Dismounting
1. To unscrew the bump head fully, introduce a
screwdriver on the coupling plate and the hole of
the transmission so as to block the piece. Unscrew
the bump head turning clockwise.
2. Unscrew clockwise the bottom part of the nylon
bump head.
3. Remove the bottom cover. Remove the empty nylon
charge and any remaining nylon thread.
Threading the new nylon
Cut approximately 4 meters of nylon thread. Hold the
both ends of the nylon thread, fold in two. Insert into
the nylon charger and coil both ends of the thread in
the same direction but each thread in its groove.
Mounting
1. Block both ends of the nylon thread in the two
grooves and on opposite orifices.
2. Reinsert the nylon charge back into place and
place the two extremes of the nylon thread in the
exit holes provided.
3. Pull each nylon thread until it is sticking out some
12 cm .
4. Mount the bump head by turning anticlockwise.
6.3. CHECK POINTS BEFORE STARTING
Do not use this machine if it becomes damaged or
wrongly regulated.
Use this machine for the purpose for which it was
designed. Any other use may be dangerous for the
user to the machine and for people, animals and
things you may have around.
- Check the machine completely and look for loose
parts (screws, nuts, etc.) and damages. Press,
repair or replace everything you need before using
the machine.
- Verify that the protective screen is properly
attached to the brush cutter.
- Check that there are not fuel leaks.
- Verify that the disk or head is not damaged.
- Check the air filter is clean. Clean the filter if
necessary.
- Do not use attachments on this machine out of
our recommendations because their use may
cause serious injury to the user, the machine and
the people, animals and things close to the
machine.
6.3.1. GASOLINE AND OIL MIX
ATTENTION: Motor fuel is highly flammable.
If the fuel or the machine burns, put the fire
off with a fire dust extinguisher.
Use unleaded fuel of 95 ° and 100% synthetic oil for
2 stroke engines.
Do not use fuel with ethanol or methanol because will
damage the engine.
Motor Fuel:
Mixture (Gasoline 40: Oil 1) 2.5%.
Exit orifices for nylon thread
Groove
Groove
Cube
Summary of Contents for BEST 310 DPG
